What causes my Exmark Lawn Mower to pull left or right?
If your Exmark Lawn Mower pulls to the left or right when the levers are fully forward, the tire pressure in the drive tires may not be correct. Adjust the tire pressure to resolve this issue.
What to do if my Exmark LAZER Z Lawn Mower cuts unevenly?
If your Exmark Lawn Mower is cutting unevenly, consider the following: * Check the air pressure in the tires, ensuring it is at 13 psi for both the drive tires and pneumatic casters. * Inspect the deck support chains. * Check the blades to ensure straightness (they should be within 3/16" or one blade width from being in line.)
How to fix uneven cuts with my Exmark Lawn Mower?
To fix uneven cuts with your Exmark Lawn Mower: * Check the drive tire pressure and tire circumference. Higher tire pressure may improve cutting height on rough terrain, while lower pressure provides more flotation. * Ensure blade spacers, axle positions, and front caster spacers are equal on each blade. * Check that all bolts on the caster mounting brackets are tight. * Verify the blades are straight tip to tip (within 3/16" or one blade width of being in line).
What to do if there is excessive grass blowout from the Exmark Lawn Mower deck?
To resolve excessive grass blowout from the deck of your Exmark Lawn Mower, try the following: * Empty the bags more frequently. * Remove any debris, leaves, or grass clippings from the screen in the bagger hood. * Reduce your ground speed while maintaining full throttle. * Install a new blower belt if the current one is worn, loose, or broken. * Locate and remove any debris plugging the tube or blower. * If conditions are dry, switch to a lower lift blade.
Why do blower components wear quickly on my Exmark LAZER Z Lawn Mower?
If the blower components on your Exmark Lawn Mower show signs of wear and/or the air cleaners and cooling fins are dirty, it may be due to sandy or dry conditions. Use low lift blades on the cutting deck and higher cutting heights. Clean air cleaners and cooling fins frequently.
What to do if my Exmark LAZER Z Lawn Mower is pulling to the side?
If your Exmark Lawn Mower pulls to the left or right (with levers fully forward), the tire pressure in drive tires may not be correct. Adjust the tire pressure in the drive tires.
Why won't my Exmark LAZER Z Lawn Mower starter crank?
The starter may not crank for several reasons: * The PTO might be engaged: Disengage the PTO. * The parking brake might not be engaged: Set the parking brake. * The drive levers might not be in the neutral lock position: Ensure the drive levers are in the neutral lock position. * The battery might not have a full charge: Charge the battery. * Electrical connections might be corroded, loose, or faulty: Check the electrical connections for good contact, clean connector terminals, apply dielectric grease, and reconnect. * A fuse might be blown: Replace the blown fuse. * Relay or switch is defective: Contact an Authorized Service Dealer. * Faulty module: Replace module.
What to do if Exmark Lawn Mower starter does not crank?
If the starter on your Exmark Lawn Mower doesn't crank, it could be due to several reasons. Ensure the PTO is disengaged and the parking brake is set. Also, make sure the drive levers are in the neutral lock position. Check if the battery has a full charge and charge it if necessary. Examine the electrical connections for corrosion or looseness; clean and reconnect them if needed. Replace any blown fuses. For relay or switch issues, or a faulty module, contact an Authorized Service Dealer or replace the module.
Why Exmark LAZER Z Lawn Mower engine will not start?
If your Exmark Lawn Mower engine won't start, ensure the battery is fully charged. Confirm the throttle control is midway between “SLOW” and “FAST,” with the choke “ON” for a cold engine or “OFF” for a warm one. Verify fuel in the tank and the fuel valve is open. The operator must be in the seat, with the seat switch properly adjusted. Make sure the parking brake is set, motion control levers are in neutral lock, and blades are disengaged. Check that spark plug wires are connected correctly, and inspect for loose or faulty wiring. Clean any corrosion from wiring connections with electrical contact cleaner, apply dielectric grease, and reconnect.
What to do if my Exmark LAZER Z engine will not start?
If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, consider the following: * The fuel tank might be empty, so fill it up. * The fuel shutoff valve could be closed, so open it. * The oil level in the crankcase might be low, so add oil. * The throttle and choke may not be correctly positioned; ensure the throttle is midway between “SLOW” and “FAST,” and the choke is “ON” for a cold engine or “OFF” for a warm engine. * A dirty fuel filter can cause starting issues, so replace it. * A dirty air cleaner can prevent the engine from starting; clean or replace the air cleaner element. * Check the seat switch indicator. Replace seat if needed. * Also, check the spark plug wire connection and clean, adjust, or replace the spark plug if faulty.
General| Engine Brand | Kawasaki |
|---|---|
| Transmission | Hydrostatic |
| Deck Construction | Fabricated or welded steel |
| Category | Commercial |
| Type | Commercial |
| Speed | 10 mph |
| Turning Radius | Zero-turn |
| Fuel Capacity | 10-15 gallons |
| Weight | 1, 465 lbs |
Outlines essential safety practices for operating the machine.
Explains the importance and meaning of safety decals on the machine.
Provides critical instructions for safe operation on slopes.
Covers operation of ignition switch, brake lever, and PTO switch.
Essential safety and operational checks before starting the engine.
Critical safety rules to follow while operating the mower.
Warnings about operating with the ROPS and its proper use.
Detailed steps for safely starting the engine.
Procedures for engaging and disengaging the power take-off.
Critical safety rules to follow before and during maintenance.
A table outlining maintenance tasks by service interval.
Common causes and solutions when the starter fails to crank.
Troubleshooting common engine starting and running problems.
Wiring diagrams for various engine and control configurations.
Diagram illustrating the machine's hydraulic system components.
To Next Page
