Exmark LAZER Z - User Manual

Other manuals for Exmark LAZER Z

Parts Manual36 pages

Setup Instructions5 pages

Questions and Answers

C
Collin MorenoAug 25, 2025
What to do if my Exmark LAZER Z engine will not start?
- M
  Monique LittleAug 26, 2025
  If your Exmark Lawn Mower engine won't start, starts hard, or fails to keep running, consider the following: * The fuel tank might be empty, so fill it up. * The fuel shutoff valve could be closed, so open it. * The oil level in the crankcase might be low, so add oil. * The throttle and choke may not be correctly positioned; ensure the throttle is midway between “SLOW” and “FAST,” and the choke is “ON” for a cold engine or “OFF” for a warm engine. * A dirty fuel filter can cause starting issues, so replace it. * A dirty air cleaner can prevent the engine from starting; clean or replace the air cleaner element. * Check the seat switch indicator. Replace seat if needed. * Also, check the spark plug wire connection and clean, adjust, or replace the spark plug if faulty.
J
Jacob YoderAug 26, 2025
Why Exmark LAZER Z Lawn Mower engine will not start?
- S
  Stephanie ShafferAug 26, 2025
  If your Exmark Lawn Mower engine won't start, ensure the battery is fully charged. Confirm the throttle control is midway between “SLOW” and “FAST,” with the choke “ON” for a cold engine or “OFF” for a warm one. Verify fuel in the tank and the fuel valve is open. The operator must be in the seat, with the seat switch properly adjusted. Make sure the parking brake is set, motion control levers are in neutral lock, and blades are disengaged. Check that spark plug wires are connected correctly, and inspect for loose or faulty wiring. Clean any corrosion from wiring connections with electrical contact cleaner, apply dielectric grease, and reconnect.
G
Gabriel GarzaAug 27, 2025
What to do if Exmark Lawn Mower starter does not crank?
- D
  Damon HaynesAug 27, 2025
  If the starter on your Exmark Lawn Mower doesn't crank, it could be due to several reasons. Ensure the PTO is disengaged and the parking brake is set. Also, make sure the drive levers are in the neutral lock position. Check if the battery has a full charge and charge it if necessary. Examine the electrical connections for corrosion or looseness; clean and reconnect them if needed. Replace any blown fuses. For relay or switch issues, or a faulty module, contact an Authorized Service Dealer or replace the module.
J
Jamie PetersonAug 27, 2025
Why won't my Exmark LAZER Z Lawn Mower starter crank?
- N
  Nicholas RodriguezAug 27, 2025
  The starter may not crank for several reasons: * The PTO might be engaged: Disengage the PTO. * The parking brake might not be engaged: Set the parking brake. * The drive levers might not be in the neutral lock position: Ensure the drive levers are in the neutral lock position. * The battery might not have a full charge: Charge the battery. * Electrical connections might be corroded, loose, or faulty: Check the electrical connections for good contact, clean connector terminals, apply dielectric grease, and reconnect. * A fuse might be blown: Replace the blown fuse. * Relay or switch is defective: Contact an Authorized Service Dealer. * Faulty module: Replace module.
N
Nancy Washington DDSAug 28, 2025
How to fix an Exmark LAZER Z that cuts unevenly?
- J
  Jessica SullivanAug 28, 2025
  If your Exmark Lawn Mower cuts unevenly, consider the following: * Check the air pressure in the drive tires, it should be 13 psi. Semi-pneumatic casters do not require inflation. * Inspect the deck support chains. * Check the blades tip to tip for straightness (they should be within 3/16" or one blade width from being in line.)
C
cheryl40Aug 29, 2025
What to do if Exmark LAZER Z Lawn Mower cuts unevenly?
- S
  Stacey CooperAug 29, 2025
  If your Exmark Lawn Mower cuts unevenly, first check the air pressure in the tires, ensuring 13 psi for drive tires and 13 psi for pneumatic casters. For rough terrain, a more uniform cutting height may be achieved with higher tire pressure. Also, inspect the deck support chains and check the blades tip to tip for straightness (they should be within 3/16" or one blade width from being in line.)
J
John HuntAug 29, 2025
How to fix Exmark LAZER Z that pulls to the left or right?
- S
  Sylvia AlexanderAug 30, 2025
  If your Exmark Lawn Mower pulls left or right with levers fully forward, move levers forward and compensate as necessary. Check the air pressure in the tires, ensuring 13 psi for the drive tires and 13 psi for the pneumatic castors. Also, check the reverse indicator and motion control linkage adjustment.
S
Stephanie SmithAug 30, 2025
How to fix uneven cuts with my Exmark Lawn Mower?
- K
  Karen DavisAug 30, 2025
  To fix uneven cuts with your Exmark Lawn Mower: * Check the drive tire pressure and tire circumference. Higher tire pressure may improve cutting height on rough terrain, while lower pressure provides more flotation. * Ensure blade spacers, axle positions, and front caster spacers are equal on each blade. * Check that all bolts on the caster mounting brackets are tight. * Verify the blades are straight tip to tip (within 3/16" or one blade width of being in line).
J
James CurtisAug 30, 2025
What to do if my Exmark LAZER Z Lawn Mower cuts unevenly?
- A
  Amy GonzalezAug 31, 2025
  If your Exmark Lawn Mower is cutting unevenly, consider the following: * Check the air pressure in the tires, ensuring it is at 13 psi for both the drive tires and pneumatic casters. * Inspect the deck support chains. * Check the blades to ensure straightness (they should be within 3/16" or one blade width from being in line.)
L
lawrencejenniferAug 31, 2025
What causes my Exmark Lawn Mower to pull left or right?
- K
  Katie ChenAug 31, 2025
  If your Exmark Lawn Mower pulls to the left or right when the levers are fully forward, the tire pressure in the drive tires may not be correct. Adjust the tire pressure to resolve this issue.

Exmark LAZER Z Specifications

General

Engine Brand	Kawasaki
Transmission	Hydrostatic
Deck Construction	Fabricated or welded steel
Category	Commercial
Type	Commercial
Speed	10 mph
Turning Radius	Zero-turn
Fuel Capacity	10-15 gallons
Weight	1, 465 lbs