Fast A10 - Axle Width Chart - Singles

77 pages

Save Page as PDF

To Next Page

To Previous Page

AXLES, TIRES, and TRACKS

AXLES, TIRES, and TRACKS Liquid Fertilizer Applicator A10 / A13 / A18 / A24 Page 36

Axle Width Chart – Singles

Main Page

Table of Contents3
Warranty Registration8
Warranty Inspection Report8
Inspections10
Pre-Delivery10
Delivery11
After-Sale12
Owner Register13
Foreword to the Owner14
Introduction16
Safety17
Safety Alert Symbols and Signal Words17
General Safety18
Prepare for Emergencies18
Wear Protective Clothing18
Protect against Noise18
Practice Safe Maintenance18
Support Raised Equipment19
Avoid Heating Near Pressurized Fluid Lines19
Avoid High-Pressure Fluids19
Inspect Lift Circuit Hoses20
Store Attachments Safely20
Electrical20
Service Tires Safely20
Dispose of Waste Properly21
Handle Agricultural Chemicals Safely21
Reduce Risk of Exposure and Injury21
Handle Chemical Products Safely22
Operate Hydraulics Safely22
Use Safety Lights and Devices23
Keep Riders off Machine23
Observe Maximum Transport Speed23
EC Compliance Notification24
Use a Signal Person24
Use a Safety Chain24
Tow Loads Safely24
Avoid Overhead Power Lines25
Prepare for Transport25
Transport Safely26
Park Safely26
Replace Safety Signs27
Hitch27
Wing28
Main Frame29
Wheel and Tracks29
Safety Features30
Sign-Off Form31
Specifications32
Tractor Power, Size Recommendation32
Hydraulic System Requirements32
Machine Dimensions & Specifications33
Preparing the Machine34
Use the Tractor Operator's Manual34
Pre-Operation Checklist34
AXLES, TIRES, and TRACKS35
Setting Axle Width35
Axle Width Chart - Singles36
Axle Width Chart - Duals37
Axle Width Chart - Tracks38
Checking Tire Pressure39
Checking Wheel Nuts40
Track Use41
General Guidelines41
Maximizing Track Life41
Track System Break-In41
Track Wear & Trash Buildup43
Undercarriage Inspection and Maintenance43
Track Service44
MID-Wheel, Wedges, Idler, and MID-Roller Cap Screws44
Check Track Alignment45
Track Alignment Procedure46
ATTACHING and DETACHING47
Attach the Machine Safely47
Attach the Machine to the Tractor47
Attach Safety Chain to Tractor48
Attach Warning Light Plug48
Connect Rate Controller or Nutrient Applicator System Wiring48
Make Proper Hose Connections49
SCV Identification Chart50
Detach Machine from Tractor51
Adjust Hitch Height51
Transporting52
Following Safe Transport Procedures52
Preparing the Machine for Transport52
Fold Toolbar for Transport52
Transport Notes and Checks53
Transporting the Machine53
Using Warning Lights53
Keep Riders off the Machine53
Caution for All Machines54
Unfolding/Extending the Toolbar54
Hydraulic Flow56
Regulating Hydraulic Flow to the Pump56
Load Sensing Closed Center System (LS Closed)56
Pressure Compensating Closed-Center System (PC Closed)56
Open Center System (Open)57
Tractor SCV Functions57
Adjust Depth Control59
Adjust Application Depth59
Adjust Gauge Wheels59
Adjust Ground Speed60
Inspect Coulters60
Adjust Nozzles61
Preparing the Liquid System62
Clean Strainer Filter62
Filling the Tank63
Filling the Product Tank63
Filling Fresh Water Rinse Tank63
Use Tank Fill Marker64
Pump & Pressure64
LUBRICATION and MAINTENANCE65
Lubricating and Maintaining the Machine Safely65
Lubricant Storage65
Grease65
Greases for Air Temperature Ranges65
Alternative and Synthetic Lubricants65
Lubrication and Maintenance Intervals66
Each 10 Hours or Daily66
Each 50 Hours or Weekly67
Before and after each Season68
As Required68
Service69
Practice Safe Maintenance69
Work in a Clean Area69
Service Machines Safely69
Support the Machine Properly70
Avoid High-Pressure Fluids70
Preventing Hydraulic System Contamination70
Replace Hydraulic Hoses71
Tightening Hardware71
Preparing for Storage72
Removing from Storage72
Tightening Hardware73
Metric Bolt and Screw Torque Values73
Unified Inch Bolt and Screw Torque Values74
Face Seal Fittings Assembly & Installation - All Pressure Applications75
Face Seal O-Ring to Stud End Installation75
Face Seal Adjustable Stud End O-Ring Installation75
Face Seal Straight Stud End O-Ring Installation75
Fitting Installation75
Assembly Torque75
SAE Face Seal and O-Ring Stud End Fitting Torque Chart76

Fast A10 - Axle Width Chart - Singles

Table of Contents