flamco Flamcomat Starter - Type Key Pump Control Unit; Type Key Controller Unit

TemplateA4_v20130506
15
Alphabetic glossary of abbreviations in terminal plan.
Note:mentionedswitchsettingsareincurrent-free,un-switchedsituation.
accessory (SPCExtensionvolume,pressureanalog,optional)
COM COMinterface;serialport
COM Thecommonport
data (Dataprotocol,optional)
drs (Diaphragmrupturesensor,optional)
extralowvoltage Protectivelowvoltage
fault Errormessage,commonerrormessageDisplayedswitchsettingiserror.
F1/2 MS1/2 (Motorcircuit-switch1/2;Motorcircuit-switchcombination1/2,SPCx-hw)
gs (Gassensor,optionalGassensorexibleconnectionassembly)
highvoltage Voltageaspermarkingsontheautomat
mains supply Power feed
mpl (Minimumpressurelimiter,optional)
M3/3.1 V3/3.1 Motor3(top-up,optional)/3.1(drainage,optional);valve3(top-up)/3.1
(drainage,optional)
M1 V4 K1/MS1 Motor2(pressureincrease);valve5(notapplicable);switch2/motorcircuit-switchcombination2,
SPCx-hw
M2 V5 K2/MS2 Motor2(pressureincrease);valve5(notapplicable);switch2/motorcircuit-switchcombination2,
SPCx-hw
niveau Level,content
ohmicload Ohmicload,resistance
option (notapplicable)
pressure Pressure
pwm (Impulsewatermeter,optional)
ps (Pressureswitch;levelswitchmin.level,top-uppump,optional)
rell/drain Top-up/(drain,optional)
sensors Sensors
tc (Temperatureswitch,optional)
V1;1.1 Valve1;1.1;parallel,airreleasevalve(pressuredrop)
V2 Valve2;airreleasevalve(pressure drop)
V2.1 Valve2.1(notapplicable)
5.3 Type key Pump control unit
Key: AB - C - D
E.g.: DP80 - 1 - 50
Nom. frequency of the operating voltage (Hz): 50 = 50 Hz; 60
= 60 Hz
Pump manufacturer:
Module version:
Performance class:
MP = Monopump; DP = Duopump
M;
2; 10; 20; 60; 80; 90; 100; 130
1; 2; 3; 4; 5
5.4 Type key Controller unit
Key: SPC x - y - A - B - C - D - E
SPC 1.2 - hw - 1 - 1 - 7 - 1 - 0
SPC 1.2 - lw
Phase monitoring/SPC-extension module, Ananlogue signalling: 0 = Not present;
Start type:
Number of motors:
Hardware version
Nominal current range:
Voltage: 1 = 400 V ± 10 % / 3 N PE / 50/60 Hz
Output range:
1 = Direct start; 2 = Soft start
1 = 1 motor; 2 = 2 motors
1 = 1.1 - 1.6; 2 = 1.4 - 2.0; 3 = 1.8 - 2.5; 4 = 2.2 - 3.2;
5 = 2.8 - 4.0; 6 = 3.5 - 5.5; 7 = 4.5 - 6.3; 8 = 5.5 - 8.0;
23 = 4.0 - 6.3; 24 = 6.3 - 10.0; 25 = 8.0 - 12.0
lw = low output
hw = high output
MP; DP / P ≤ 2.2 kW
1 = Present
9 = 7.0 - 10.0; 20 = 1.0 - 1.6; 21 = 1.6 - 2.5; 22 = 2.5 - 4.0;
N
N
N
E.g.:
MP / P ≤ 4,0 kW;
DP / P ≤ 8,0 kW
ENG