Fujitsu AOTG36LATT User Manual

En-11
Selecting the Function Number and Setting Value
[Cool model]
(1) Press the TEMP. (
 / ) buttons to select the func-
tion number.(Press the ECONOMY button to switch
betweentheleftandrightdigits.)
(2) Press the POWERFULbutton to proceed to setting
value.(PressthePOWERFULbuttonagaintoreturnto
thefunctionnumberselection.)
(3) PresstheTEMP.(
/ )buttonstoselectthesetting
value.(PresstheECONOMYbuttontoswitchbetween
theleftandrightdigits.)
(4) Press the MODE button, and START/STOP button, in
theorderlistedtoconrmthesettings.
(5) PresstheRESETbuttontocancelthefunctionsetting
mode.
(6) Aftercompleting theFUNCTION SETTING,be sureto
turn off the power and turn it on again.
Function Number
Setting
Value
CAUTION
Afterturningoffthepower,wait30secondsormorebeforeturningonitagain.The
function setting does not become active unless the power is turned off then on again.
Filter sign
Selectappropriateintervalsfordisplayingtheltersignontheindoorunitaccordingtothe
estimated amount of dust in the air of the room.
Iftheindicationisnotrequired,select“Noindication”(03).
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
Standard(400hours)
11
00
Longinterval(1,000hours) 01
Shortinterval(200hours) 02
♦ Noindication 03
Room temperature control for cooling
Dependingon theinstalledenvironment,correctionoftheroomtemperaturesensormay
be required. Select the appropriate control setting according to the installed environment.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Standard
30
00
Slightly lower control 01
Lower control 02
Higher control 03
Room temperature control for heating [Reverse cycle model only]
Dependingon theinstalledenvironment,correctionoftheroomtemperaturesensormay
be required. Select the appropriate control setting according to the installed environment.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Standard
31
00
Lower control 01
Slightly higher control 02
Higher control 03
Auto restart
Enable or disable automatic restart after a power interruption.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Enable
40
00
Disable 01
*Autorestartisan emergencyfunction suchas forpoweroutageetc.Donotattempt to
use this function in normal operation. Be sure to operate the unit by remote controller or
otherexternalinputdevice.
Room temperature sensor switching
(Onlyforwirelessremotecontroller)
WhenusingtheWiredremotecontrollertemperaturesensor,changethesettingto“Both”
(01).
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Indoor unit
42
00
Both 01
00:Sensorontheindoorunitisactive.
01:Sensorsonbothindoorunitandwiredremotecontrollerisactive.
Remote controller signal code
(Onlyforwirelessremotecontroller)
The indoor unit signal code can be changed. Select the appropriate signal code.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ A
44
00
B 01
C 02
D 03
External input control
“Operation/Stop”modeor“Forcedstop”modecanbeselected.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Operation/Stopmode
46
00
(Settingforbidden) 01
Forced stop mode 02
Indoor unit fan control for energy saving for cooling
Enables or disables the power-saving function by controlling the indoor unit fan rotation when
the outdoor unit is stopped during cooling operation.
(♦...Factorysetting)
Setting Description
Function
Number
Setting Value
♦ Disable
49
00
Enable 01
00:Whentheoutdoorunitisstopped,theindoorunitfanoperatescontinuouslyfollowing
the setting on the remote controller.
01:Whentheoutdoorunitisstopped,theindoorunitfanoperatesintermittentlyatavery
low speed.
Setting record
Record any changes to the settings in the following table.
Setting Description Setting Value
Filter sign
Room temperature control for cooling
Room temperature control for heating
Autorestart
Room temperature sensor switching
Remote controller signal code
Externalinputcontrol
Indoor unit fan control for energy saving for cooling
AftercompletingtheFUNCTION SETTING, be suretoturn off thepowerandturn it on
again.
ASTG18KMCA_中型標準モデルLM系_R32_0724m.indd 11 2013/07/24 16:52:18

Fujitsu AOTG36LATT Specifications

General

Brand	Fujitsu
Model	AOTG36LATT
Category	Air Conditioner
Language	English