EasyManua.ls Logo

Fujitsu ESPRIMO P372 Series - User Manual

Fujitsu ESPRIMO P372 Series
52 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
System
Operating Manual
ESPRIMO P15xx / P2440
ESPRIMO P2540 / P2550
ESPRIMO P2560 / P2760
ESPRIMO P352x / P372x

Table of Contents

Questions and Answers

  • L
    Linda GarciaAug 14, 2025
    Why does my Fujitsu ESPRIMO P372 Desktop monitor remain blank?
    • B
      burgessblakeAug 14, 2025
      If the Fujitsu Desktop monitor remains blank, several factors could be at play. First, ensure the monitor is powered on. If power saving mode is active, press any key or deactivate the screen saver, entering your password if prompted. Check the brightness setting and adjust if it's too low. Verify that the power and monitor cables are securely connected to both the device and a grounded mains outlet.
  • N
    Nicole EvansAug 17, 2025
    How to fix a Fujitsu ESPRIMO P372 with power indicator off?
    • T
      Travis RobinsonAug 18, 2025
      If the power indicator on your Fujitsu Desktop remains off after switching it on, it could be due to a faulty mains voltage supply. Ensure the power cable is correctly plugged into the device and a grounded mains outlet, and that the main switch at the rear is set to the "I" position. If the internal power supply is overloaded, pull the power plug out, wait a moment, plug it back in, and try switching the device on again.
  • C
    Crystal ValenciaAug 21, 2025
    What to do if no mouse pointer is displayed on Fujitsu ESPRIMO P372 Desktop?
    • C
      Catherine RobinsonAug 21, 2025
      If there's no mouse pointer displayed on the screen of your Fujitsu Desktop, it's possible the mouse isn't correctly connected. Properly shut down the operating system and switch off the device. Check the mouse cable connection to the system unit, including any adapters or extension leads. Ensure only one mouse is connected before switching the device back on.
  • C
    Catherine Sullivan DDSAug 25, 2025
    What to do if Fujitsu ESPRIMO P372 cannot be switched off?
    • M
      Mrs. Sandra DavisAug 26, 2025
      If your Fujitsu Desktop cannot be switched off with the ON/OFF switch, first, try pressing the ON/OFF switch again. If that doesn't work, the system may have crashed. In this case, keep the on/off switch pressed for at least 4 seconds until the machine switches off. Be aware that this can lead to data loss and potential error messages upon the next system start.
  • C
    Carlos LiAug 27, 2025
    How to correct the time and date on a Fujitsu ESPRIMO P372 Desktop?
    • P
      Paul GarciaAug 27, 2025
      If the time and/or date is not correct on your Fujitsu Desktop, set the correct time and date within the operating system. Alternatively, set the correct time and/or date in the BIOS Setup. If the time and date are repeatedly wrong when you switch on your device, the lithium battery may be discharged and needs replacement.
  • P
    princeryanAug 31, 2025
    Why the floppy disk cannot be read or written on Fujitsu ESPRIMO P372?
    • C
      Christopher Herring DDSAug 31, 2025
      If the floppy disk cannot be read or written on your Fujitsu Desktop, check whether the write protection of the floppy disk or the floppy disk drive is activated. Also, verify in the BIOS Setup that the floppy disk drive controller is enabled. Finally, ensure that the cables of the floppy disk drive are properly connected.
  • B
    Breanna StephensSep 3, 2025
    How to fix wrong monitor settings on Fujitsu ESPRIMO P372 with Windows XP?
    • D
      Diana JonesSep 3, 2025
      Restart the Fujitsu Desktop. Press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears. If the menu for selecting the operating system appears, press F8. Select Safe Mode or Safe Mode with Network. Go to Start – Settings – Control Panel – Display and the tabs Appearance, Themes, Settings to set the correct values for the connected monitor as described in the operating manual of the monitor.
  • J
    John YorkSep 6, 2025
    How to correct incorrect monitor settings in Windows Vista on Fujitsu ESPRIMO P372?
    • J
      Justin LongSep 7, 2025
      Restart the Fujitsu Desktop. Press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system will appear. If the menu for selecting the operating system appears, press the F8 key. Select Safe Mode or Safe Mode with Network. Go to Start symbol – (Settings) – Control Panel – Appearance and Personalization – Personalization and enter the correct values for the connected monitor as described in the operating manual of the monitor.
  • T
    Tracy JordanSep 9, 2025
    How to configure the correct monitor settings on a Fujitsu ESPRIMO P372 Desktop running Windows 7?
    • L
      Lawrence PenaSep 10, 2025
      Restart the Fujitsu Desktop. Press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system appears. If the menu for selecting the operating system appears, press F8. Select Safe Mode or Safe Mode with Network. Go to Start – Control Panel – Appearance and Personalization – Display to enter the correct values for the connected monitor as described in the operating manual of the monitor.

Fujitsu ESPRIMO P372 Series Specifications

General IconGeneral
Power SupplyUp to 300W
RAMUp to 32GB
GraphicsIntel HD Graphics
Operating SystemWindows 10 Pro
Form FactorTower
PortsUSB 3.0, USB 2.0
AudioRealtek
Optical DriveDVD SuperMulti
NetworkingGigabit Ethernet

Related product manuals