What to do if the Fujitsu ESPRIMO P5635 Desktop monitor cable is not connected?
If the monitor cable is not connected, switch off the monitor and the Fujitsu Desktop. Check that the monitor cable is properly connected to the device and monitor. Then, switch on the monitor and the device.
Why is my Fujitsu Desktop monitor blank?
Your Fujitsu Desktop monitor might be blank because it is switched off. Please, switch it on. It is also possible that power saving has been activated. In this case, press any key on the keyboard, or deactivate the screen saver. If necessary, enter the appropriate password. Another reason might be that the brightness control is set to dark, so adjust the brightness control. Finally, check that the power cable is properly connected to the monitor and to a grounded mains outlet or to the monitor socket of the device and that the device power cable is properly plugged into the device and a grounded mains outlet. After checking the connections, switch on the monitor and the device.
How to fix incorrect time and date on Fujitsu ESPRIMO P5635?
If the time and/or date is not correct on your Fujitsu Desktop, set the correct time and date within the operating system you are using, or set the correct time and/or date in the BIOS Setup. If the time and date are repeatedly wrong when you switch on your device, replace the lithium battery.
What to do if Fujitsu ESPRIMO P5635 Desktop won't switch off?
If your Fujitsu Desktop cannot be switched off with the ON/OFF switch, it might not have been switched on with the switch initially, so try pressing the ON/OFF switch again. Alternatively, the system may have crashed. In this case, press and hold the ON/OFF switch for at least 4 seconds until the device switches off. Note that this will not shut down the operating system properly, and error messages may appear the next time the system is booted.
How do I fix no mouse pointer on my Fujitsu Desktop?
If there is no mouse pointer displayed on the screen of your Fujitsu Desktop, the mouse may not be correctly connected. Shut down the operating system properly, switch the device off, and check that the mouse cable is properly connected to the system unit. Also, if you are using an adapter or extension lead, check those connections. Make sure that only one mouse is connected, and then switch the device back on. Another possible cause is that the mouse controller is not enabled. Check in the BIOS Setup that the mouse controller is enabled and that the mouse driver is properly installed and present when the application program is started.
What to do if Fujitsu Desktop floppy disk cannot be read?
If the floppy disk in your Fujitsu Desktop cannot be read or written, check that the write protection of the floppy disk or the floppy disk drive is not activated. Also, verify in the BIOS Setup that the floppy disk drive controller is enabled. Finally, check that the cables of the floppy disk drive are properly connected.
How to correct wrong monitor settings in Windows Vista on Fujitsu Desktop?
To correct an incorrect monitor setting in Windows Vista on your Fujitsu Desktop, restart the device and press F8 while the system is booting. Either the Windows Advanced Start Options menu or the menu for selecting the operating system will appear. If the menu for selecting the operating system appears, press the F8 key. Select Safe Mode or Safe Mode with Network. Go to Start symbol – (Settings) – Control Panel – Appearance and Personalization – Personalization and enter the correct values for the connected monitor as described in the operating manual of the monitor.
How to correct wrong monitor settings in Windows XP on Fujitsu ESPRIMO P5635?
To correct a wrong monitor setting in Windows XP on your Fujitsu Desktop, restart the device. Press F8 while the system is booting to access either the Windows Advanced Start Options menu or the menu for selecting the operating system. If the menu for selecting the operating system appears, press F8. Select Safe Mode or Safe Mode with Network. Go to Start – Settings – Control Panel – Display and the tabs Appearance, Themes, Settings to set the correct values for the connected monitor as described in the operating manual of the monitor.
What to do if my Fujitsu Desktop power indicator remains off?
If the power indicator on your Fujitsu Desktop remains off, it could be due to a faulty mains voltage supply. Check that the power cable is correctly plugged into the device and into a grounded mains outlet, and that the main switch at the rear of the monitor is set to the "I" position. Then, switch the device on. Alternatively, the internal power supply might be overloaded. In this case, pull the power plug of the device out of the mains outlet, wait a moment, plug it back into a properly grounded mains outlet, and switch the device on.
What to do if Fujitsu Desktop won't switch on (0 Watt devices)?
If your Fujitsu Desktop is a 0-Watt device and it will not switch on, the lithium battery might be discharged. Press the emergency on button at the rear of the device, see chapter "Switching on a device when the lithium battery is discharged (0-Watt devices)."
To Next Page
General