FUTABA 32MZ-WC - S.BUS Basic Menu

200
＜
Model Menu (Helicopter)
＞
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
+(/,&237(5
S.BUSBasicMenu
S.BUSBasicMenu
Thechannelofeachfunction
canbechanged.
ThisresetstheS.BUSchannelassign-
mentsbacktothedefaults.
The
"
6%86%$6,&
"
screen is accessed via the
"
%$6,&0(18
"
VFUHHQ6HWWKH&+IRUHDFKIXQFWLRQDFFRUGLQJWRWKHWUDQVPLWWHUWREHXVHG
Any unused functions should be set to INH (Inhibited). For example, if the Gain A/E and Gain RUD remote gain functions are not going to
EHXVHGWKHQVHWWKHPWR>,1+@7KH&*<5&*<ZLOOWKHQDOORZ\RXWRPDNHJDLQDGMXVWPHQWVZLWKLQWKHUHVSHFWLYHPHQX
WARNING

 AlwaysverifythattheS.BUSfunctionas-
signmentsmatchyourtransmitterʼ sfunction
(intheFUNCTIONmenu)assignments.Ifany
changesaremade withinthetransmitterfunc
-
tionassignments,thenitwillalsobenecessary
tomakethechangeswithintheS.BUSfunction
assignments.Tochangethechannel,CGYand
T32MZ-WCmustbeconnected.
ELE2 channel Servo Type
(IfyouwanttousetheELE2portforpurposesotherthanswash.)
ThisselectstheELE2servotypes.Therearethreetypesoftheservo
drivingfrequencyselection,AN:70
 Hz,DG285  Hz,and760  μ S.All
FutabadigitalservoscanbeoperatedwithfastestDG:285
 Hzmodebut
someofotherbrandsofservosdonotsupportDG:285
 Hzmode.Inthis
case,selecttheproperservodrivingfrequencyperthemanufacturerʼ s
specifications.
IfyouselectH4-00orH4-45with4servoswashes,cannotsetthisELE2
portservotype.Inthatcase,selectallswashservotypesinSWHbasic
servotype.
Setting:AN:70  Hz/DG:760  μS/DG:285  Hz Initialsetting:DG:285  Hz
WARNING
Theservotype parameterwithinthe CGYmustmatchthetypeof
servoyouareusing.IncorrectsettingmaydamagetheCGYortheser
-
vo.Incorrectsettingmayalsoresultinalossofcontrolduringflight.
S. BUS connection: Condition on change channel
Usingthemethodologydescribedpreviously,determinethe"CondCH#"and
settheconditionchangechannelofthetransmitter.Inthisexample,DG1is
theconditionalchangechannel.
Aswiththeflightconditionfunctionofthetransmitter,itispossibleto
utilizepre-determinedsettings,eachactivatedbyaswitchorswitcheson
thetransmitter.Bysettingtheconditionswitchonthechannelwiththe
AFRfunctionofthetransmitterandsettingthepointforeachflightcondi
-
tionwiththeAFRpointcurve,youcanswitchtheconditionofCGY760R/
CGY755inconjunctionwiththeflightconditionswitchofthetransmitter.
Wireless channel
Thewirelesschannelusestwoconsecutivechannels.Forexample,ifCH13is
setto"#1",CH14isautomaticallysetto"#2".Therefore,whenusingthisfunc
-
tion,twoconsecutivefreechannelsarerequiredforthetransmitter.Itisnot
possibletouseachannelassignthatisusedforanotherfunction.
CAUTION
 Besuretochecktheoperationforallconditions1to5beforeflying.
Thesettingof"wirelessCH"ispossibleonlywhenthetransmitterand
theCGYarepoweredoffandtheCGYisturnedon.
 BesuretoconnectanddisconnecttheCGYandT32MZ-WCconnection
cablewiththepoweroff.
2consecutivefreechannels