GE Advent User Manual

31
Advent Commercial Fire System
Advanced Settings
&$87,21
Only qualified persons should make changes to advanced
phone settings.
Number of Attempts
zz003 (Phone-Pagers)
(Default = 3) Set the number of times (attempts) the panel will try
to dial the pager phone number.
To set the Number of Dial Attempts:
Once the item number has been entered, enter the number of dial
attempts (3–10) and press ƒ.
Comm Format
zz004 (Phone-Pagers)
(Default = 1 [TAP at 1200 bps PSK]) Select the type of
communication format the panel will use when reporting events
to pagers.
Communication Formats:
 Enter 0 for TAP at 300 bps (FSK)
 Enter 1 for TAP at 1200 bps (PSK)
To set the Communication Format:
Once the item number has been entered, use the choices above to
select a communication format. Press ƒ to apply the new setting.
Character Format
zz005 (Phone-Pagers)
(Default = 1 [7/E/1]) Select the character format the panel will use
when reporting to pagers.
Character Formats:
 Enter 0 for 8/N/1
 Enter 1 for 7/E/1
To set the Character Format:
Once the item number has been entered, press 0 for 8/N/1
character format (off), or 1 for 7/N/1 character format (on). Press
ƒ to apply the setting.
Pager System Reports
zz006 (Phone-Pagers)
(Default = off) Select whether or not you want system events
reported to pager.
To turn System Pager Report On/Off:
Once the item number has been entered, enter 1 to turn this
setting on (report), or 0 to turn it off (don’t report). Press ƒ to
apply the new setting.
Partition/Area 1 Pager Reports
Partition/Area 2 Pager Reports
Partition/Area 3 Pager Reports
Partition/Area 4 Pager Reports
Partition/Area 5 Pager Reports
Partition/Area 6 Pager Reports
Partition/Area 7 Pager Reports
Partition/Area 8 Pager Reports
1: zz007, 2: zz008, 3: zz009, 4: zz010,
5: zz011, 6: zz012, 7: zz013, 8: zz014 (Phone-Pagers)
(Defaults = 0, phone 25-31 = 1) Select whether or not you want
partition/area events to report to pager(s).
To turn Partition/Area Report On/Off:
Once the item number has been entered, enter 1 to turn this
setting on (report), or 0 to turn it off (don’t report). Press ƒ to
apply the new setting.
Pager PIN #
zz015 (Phone-Pagers)
(Default = none) Enter up to a 15-digit pager PIN.
To enter a Pager PIN:
1. Enter the desired item number (ex. 25015).
2. Enter up to a 15-digit (0–9) pager PIN.
3. Press
ƒ and the touchpad displays the pager PIN.
Pager Max Message Length
zz016 (Phone-Pagers)
(Default = 120 characters) Set the maximum character length for
pager messages.
To set the maximum Pager Message Length:
Once the item number has been entered, enter the maximum
pager length (0–255) and press ƒ.
Maximum Ring Cycle Time
17018 (Phone-Advanced Dialog Screen)
(Default = 67 milliseconds) Specify (in milliseconds) the
maximum cycle time for a ring signal.
To set the Maximum Ring Cycle Time:
Once the item number has been entered, specify the maximum
ring cycle time (0–255). Press ƒ to apply the new setting.

GE Advent Specifications

General

Brand	GE
Model	Advent
Category	Security System
Language	English