5-150 F60 Feeder Protection System GE Multilin
5.5 FLEXLOGIC 5 SETTINGS
5
ELEMENT
Frequency rate of
change
FREQ RATE 1 PKP
FREQ RATE 1 DPO
FREQ RATE 1 OP
The frequency rate of change 1 element has picked up
The frequency rate of change 1 element has dropped out
The frequency rate of change 1 element has operated
FREQ RATE 2 to 4 Same set of operands as shown for FREQ RATE 1
ELEMENT:
FlexElements
FxE 1 PKP
FxE 1 OP
FxE 1 DPO
FlexElement 1 has picked up
FlexElement 1 has operated
FlexElement 1 has dropped out
FxE 2 to 8 Same set of operands as shown for FxE 1
ELEMENT:
Ground
instantaneous
overcurrent
GROUND IOC1 PKP
GROUND IOC1 OP
GROUND IOC1 DPO
Ground instantaneous overcurrent 1 has picked up
Ground instantaneous overcurrent 1 has operated
Ground instantaneous overcurrent 1 has dropped out
GROUND IOC2 to 8 Same set of operands as shown for GROUND IOC 1
ELEMENT:
Ground time
overcurrent
GROUND TOC1 PKP
GROUND TOC1 OP
GROUND TOC1 DPO
Ground time overcurrent 1 has picked up
Ground time overcurrent 1 has operated
Ground time overcurrent 1 has dropped out
GROUND TOC2 to 4 Same set of operands as shown for GROUND TOC1
ELEMENT
High impedance
fault detection
(Hi-Z)
HI-Z ARC DETECTED
HI-Z ARC DETECTED-A
HI-Z ARC DETECTED-B
HI-Z ARC DETECTED-C
HI-Z ARC DETECTED-N
HI-Z ARC DETECTED DPO
HI-Z ARMED
HI-Z DISARMED
HI-Z DOWNED COND
HI-Z DOWNED COND-A
HI-Z DOWNED COND-B
HI-Z DOWNED COND-C
HI-Z DOWNED COND-N
HI-Z ARC SUSPECTED
HI-Z ARC SUSPECTED-A
HI-Z ARC SUSPECTED-B
HI-Z ARC SUSPECTED-C
HI-Z ARC SUSPECTED-N
HI-Z IOC A
HI-Z IOC B
HI-Z IOC C
HI-Z LOSS OF LOAD-A
HI-Z LOSS OF LOAD-B
HI-Z LOSS OF LOAD-C
The high impedance fault detection element has operated
The high impedance fault detection phase A element has operated
The high impedance fault detection phase B element has operated
The high impedance fault detection phase C element has operated
The high impedance fault detection neutral element has operated
No arcing has been detected
The high impedance fault detection element is in the armed state
The high impedance fault detection element is in the disarmed state
The high impedance fault downed conductor element has operated
The high impedance fault downed conductor phase A element has operated
The high impedance fault downed conductor phase B element has operated
The high impedance fault downed conductor phase C element has operated
The high impedance fault downed conductor neutral element has operated
The high impedance fault detection arcing suspected element has operated
The high impedance fault arcing suspected phase A element has operated
The high impedance fault arcing suspected phase B element has operated
The high impedance fault arcing suspected phase C element has operated
The high impedance fault arcing suspected neutral element has operated
The high impedance instantaneous overcurrent A element has operated
The high impedance instantaneous overcurrent B element has operated
The high impedance instantaneous overcurrent C element has operated
The high impedance fault phase A loss of load element has operated
The high impedance fault phase B loss of load element has operated
The high impedance fault phase C loss of load element has operated
ELEMENT:
Incipient cable fault
detection
INCIPNT FLT 1 OP
INCIPNT FLT 1 OP A
INCIPNT FLT 1 OP B
INCIPNT FLT 1 OP C
INCIPNT FLT 1 PKP
INCIPNT FLT 1 PKP A
INCIPNT FLT 1 PKP B
INCIPNT FLT 1 PKP C
Asserted when incipient cable fault detector 1 operates in any phase
Asserted when incipient cable fault detector 1 operates in phase A
Asserted when incipient cable fault detector 1 operates in phase B
Asserted when incipient cable fault detector 1 operates in phase C
Asserted when incipient cable fault detector 1 picks up in any phase
Asserted when incipient cable fault detector 1 picks up in phase A
Asserted when incipient cable fault detector 1 picks up in phase B
Asserted when incipient cable fault detector 1 picks up in phase C
INCIPNT FLT 2 Same set of operands as shown for INCIPNT FLT 1
ELEMENT
Non-volatile latches
LATCH 1 ON
LATCH 1 OFF
Non-volatile latch 1 is ON (Logic = 1)
Non-volatile latch 1 is OFF (Logic = 0)
LATCH 2 to 16 Same set of operands as shown for LATCH 1
ELEMENT:
Load encroachment
LOAD ENCHR PKP
LOAD ENCHR OP
LOAD ENCHR DPO
Load encroachment has picked up
Load encroachment has operated
Load encroachment has dropped out
ELEMENT:
Negative-sequence
directional
overcurrent
NEG SEQ DIR OC1 FWD
NEG SEQ DIR OC1 REV
NEG SEQ DIR OC2 FWD
NEG SEQ DIR OC2 REV
Negative-sequence directional overcurrent 1 forward has operated
Negative-sequence directional overcurrent 1 reverse has operated
Negative-sequence directional overcurrent 2 forward has operated
Negative-sequence directional overcurrent 2 reverse has operated
ELEMENT:
Negative-sequence
instantaneous
overcurrent
NEG SEQ IOC1 PKP
NEG SEQ IOC1 OP
NEG SEQ IOC1 DPO
Negative-sequence instantaneous overcurrent 1 has picked up
Negative-sequence instantaneous overcurrent 1 has operated
Negative-sequence instantaneous overcurrent 1 has dropped out
NEG SEQ IOC2 Same set of operands as shown for NEG SEQ IOC1
Table 5–18: F60 FLEXLOGIC OPERANDS (Sheet 3 of 8)
OPERAND TYPE OPERAND SYNTAX OPERAND DESCRIPTION
To Next Page
Loading...
