GE MAC 1600

To Next Page

To Previous Page

EMC-CompliantSupplies&Accessories

PartNumberDescription

2035628-001

BarcodeReaderCable

3700031-002

LANCable

2038704-001

InternalModem

416070-001

ExternalVGACable

144MAC™16002028451-183E

Main Page

Table of Contents3
Introduction7
Intended User7
Indications for Use7
Contraindications7
Prescription Device Statement7
Regulatory and Safety Information8
Safety Conventions8
Safety Hazards8
Parts and Accessories Information9
Responsibility of the Manufacturer9
Responsibility of the Purchaser/Customer9
Symbols10
Training13
Equipment Identification13
Product Label13
Serial Number Format14
Product Codes14
Service Information15
Service Requirements15
Additional Assistance15
Manual Information15
Intended Audience15
Manual Purpose15
Document Conventions15
Related Documents17
Equipment Overview19
Front View19
Side View20
Rear View21
Keyboard22
Keyboard (Stress Option)24
Block Diagram26
Hardware/Firmware Architecture27
Troubleshooting29
General Fault Isolation29
Power up Self-Test29
Poor Quality Ecgs30
Visual Inspection30
Event Logging31
Setting up Event Logging31
Exporting the Event Log33
Performing Diagnostic Tests33
Accessing the System Diagnostics Function33
Testing the Display35
Testing the Speaker36
Testing the Keyboard37
Testing the Acquisition Module38
Checking Battery Status38
Testing the Writer39
Testing the RS232 Port42
Testing the LAN Option43
Testing the Modem44
Testing the USB Port45
Testing the Patient Lead Wires46
Equipment Problems: ECG Data Noise46
Error Codes47
Acquisition Error Codes47
Printer Error Codes49
Frequently Asked Questions50
Maintenance50
System Setup53
Clinical55
Navigating the User Interface55
Maintenance59
Recommended Maintenance59
Required Tools and Supplies59
FRU Replacement Procedures60
High Level FRU Identification60
Preparing System for FRU Replacement61
Replacing the Patient Cable61
Replacing Barcode Reader or Barcode Reader Cable62
Replacing the Paper Tray Assembly64
Replacing the Battery64
Replacing the Keyboard67
Replacing the Display Assembly71
Replacing the Internal Modem (Option)71
Replacing the Power Supply Assembly72
Replacing the Acquisition Board Assembly75
Replacing the KISS Pump Assembly (Option)77
Replacing the Printer Assembly80
Replacing the Printer Board86
Replacing the Printhead88
Replacing the Optical Sensors92
Replacing the Mainboard/Ete Module Assembly94
Functional Checkout99
Visual Inspection100
Functional Checkout Procedures101
Electrical Safety Checks102
Updating Software104
Conditioning the Battery Pack106
Parts Lists109
Ordering Parts109
General Information109
Field Replaceable Units (Frus)110
MAC 1600 Upper Level Assembly, PN 2032093110
Power Supply FRU Kit, PN 2035703-001117
Mainboard ETE Assembly FRU Kit, PN 2035704-001117
Acquisition Assembly FRU Kit, PN 2035705-001117
Cable Harness FRU Kit, PN 2035707-001117
Display Cover Assembly FRU Kit, PN 2035706-001118
Printer Assembly FRU Kit, PN 2035702-001118
Paper Tray and Printer Door FRU Kit, PN 2035711-001118
Display Assembly FRU Kit, PN 2035700-001118
Printer Board Assembly FRU Kit, PN 2036813-001119
KISS Pump Assembly FRU Kit, PN 2036814-001119
KISS Pump Hardware FRU Kit, PN 2036815-001119
Internal Modem FRU Kit, PN 2036816-001119
Printhead FRU Kit, PN 2036817-001120
Optical Sensor and Bracket FRU Kit, PN 2036818-001120
Fastener Hardware FRU Kit, PN 2035708-001121
Middle and Base Plastic FRU Kit, PN 2036812-001122
Plastics Kit, PN 2035709-001122
Keyboards, Non-Stress123
Keyboards, Stress124
Data Matrix Barcode Scanner Kits125
Power Cords126
Technical Specifications129
Electromagnetic Compatibility133
Electromagnetic Compatibility (EMC)133
Guidance and Manufacturer's Declaration - Electromagnetic Emissions133
Guidance and Manufacturer's Declaration - Electromagnetic Immunity134
Guidance and Manufacturer's Declaration - Electromagnetic Immunity136
Recommended Separation Distances137
EMC Exceptions Disclosure139
EMC-Compliant Supplies & Accessories141
Introduction141
Standard Accessories141

Table of Contents

Other manuals for GE MAC 1600

Related product manuals