EasyManuals Logo

GE NX-10 Installer Manual

GE NX-10
257 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #214 background imageLoading...
Page #214 background image
LOC DESCRIPTION DEFAULT PROGRAMMING DATA
2 Polling enable (for UL AA) 2 Reserved
3 Reserved 3 Reserved
4 Reserved
4 TCP/IP Reporting in SIA (Contact ID if off)
5 Reserved 5 Reserved
6 Reserved 6 Reserved
7 Reserved
7 Use 3-DES encryption
8 Reserved
8 Up/downloading using GSM CSD (GSM GPRS if off)
1 DESTINATION SELECTION FOR REPORT
CONTROL 1
0
2 BACKUP DESTINATION SELECTION FOR REPORT
CONTROL 1
0
3 REPORT DELAY FOR REPORT CONTROL 1
0
EVENT SELECTION FOR REPORT CONTROL 1 (BY PARTITION)
Segment 1
Alarms and Restores
1-2-3-4-5-6-7-8
Segment 2
Open/Close
1-2-3-4-5-6-7-8
Segment 3
Bypass
1-2-3-4-5-6-7-8
Segment 4
Zone Trouble
1-2-3-4-5-6-7-8
Segment 5
Power Trouble (AC Failure / Low
Batt.)
1-2-3-4-5-6-7-8
Segment 6
Siren & Telephone Fault
1-2-3-4-5-6-7-8
Segment 7
Test Reports
1-2-3-4-5-6-7-8
Segment 8
Program, Download, & Log Full
1-2-3-4-5-6-7-8
Segment 9
Tampers (zones and box)
1-2-3-4-5-6-7-8
Segment 10
Short Circuit
1-2-3-4-5-6-7-8
Segment 11
Sensor Lost
1-2-3-4-5-6-7-8
Segment 12
Sensor Low Battery
1-2-3-4-5-6-7-8
Segment 13
Expander Trouble (incl. keypad)
1-2-3-4-5-6-7-8
Segment 14
Failure To Communicate
1-2-3-4-5-6-7-8
Segment 15
Zone Activity Monitoring
1-2-3-4-5-6-7-8
4
Segment 16
Reserved
1-2-3-4-5-6-7-8
5 DESTINATION SELECTION FOR REPORT
CONTROL 2
0
6 BACKUP DESTINATION SELECTION FOR REPORT
CONTROL 2
0
7 REPORT DELAY FOR REPORT CONTROL 2
0
EVENT SELECTION FOR REPORT CONTROL 2 (BY PARTITION)
Segment 1
Alarms and Restores
0-0-0-0-0-0-0-0
Segment 2
Open/Close
0-0-0-0-0-0-0-0
Segment 3
Bypass
0-0-0-0-0-0-0-0
Segment 4
Zone Trouble
0-0-0-0-0-0-0-0
Segment 5
Power Trouble (AC Failure / Low
Batt.)
0-0-0-0-0-0-0-0
Segment 6
Siren & Telephone Fault
0-0-0-0-0-0-0-0
Segment 7
Test Reports
0-0-0-0-0-0-0-0
Segment 8
Program, Download, & Log Full
0-0-0-0-0-0-0-0
Segment 9
Tampers (zones and box)
0-0-0-0-0-0-0-0
Segment 10
Short Circuit
0-0-0-0-0-0-0-0
Segment 11
Sensor Lost
0-0-0-0-0-0-0-0
Segment 12
Sensor Low Battery
0-0-0-0-0-0-0-0
Segment 13
Expander Trouble (incl. keypad)
0-0-0-0-0-0-0-0
Segment 14
Failure To Communicate
0-0-0-0-0-0-0-0
Segment 15
Zone Activity Monitoring
0-0-0-0-0-0-0-0
8
Segment 16
Reserved
0-0-0-0-0-0-0-0
9 DESTINATION SELECTION FOR REPORT
CONTROL 3
0

Table of Contents

Other manuals for GE NX-10

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the GE NX-10 and is the answer not in the manual?

GE NX-10 Specifications

General IconGeneral
BrandGE
ModelNX-10
CategorySecurity System
LanguageEnglish

Related product manuals