gefran 650 - Page 5

80208G_MHW_650-1250-1350_01-2017_ENG
3
output ................................................................................. 104
4.17.1. S.o.A1 - Defining the state of the analog output .....105
4.17.2. t.o.A1 - Defining the type of analog output ..............105
4.17.3. F.o.A1 - Selecting the function assigned to the analog
output .......................................................................105
4.17.4. LO.A1 - Scale minimum ........................................... 105
4.17.5. HI.A1 - Scale maximum ...........................................106
4.18. VALVE Submenu – Configuring valve parameters .............107
4.18.1. F.uAL - Defining valve function ................................108
4.18.2. KEY.MO - Enabling valve operation with keys ......... 108
4.18.3. TRAVL - Valve actuator travel time ..........................108
4.18.4. TIM.LO - Minimum power change for valve drive ....108
4.18.5. TIM.HI - Impulse mode setpoint ..............................108
4.18.6. TIM.ON - Minimum valve impulse time or ON time in
impulse mode ..........................................................109
4.18.7. TIM.OF - OFF time in impulse mode.......................109
4.18.8. DEAD.B - Deadzone symmetrical to setpoint ..........109
4.19. MODE Submenu – Configuring functioning mode ............. 110
4.19.1. PID.G.N - Number of groups of control parameters 111
4.19.2. MA.AU - Defining transition from Manual to Automatic .
111
4.19.3. AU.MA - Defining transition from Automatic to Manual .
111
4.19.4. LO.rE - Defining transition from remote SP to local SP .
111
4.19.5. On.OF - Enabling software on/off ............................112
4.19.6. MA.P.L - Enabling manual power latch .................... 112
4.19.7. MAn.P - Enabling change of manual power value ...112
4.19.8. dIG - Defining type of digital inputs .........................112
4.19.9. ALRM.N - Number of alarms enabled ......................112
4.19.10. tMEr - Enabling Timer function ................................113
4.19.11. MUL.SP - Enabling Multiset function .......................113
4.19.12. SP.REM - Enabling the remote setpoint ...................113
4.19.13. SPr.t - Defining absolute or deviation remote setpoint ..
113
4.19.14. PROGR - Enabling the setpoint programmer ..........113
4.19.15. t.Pro - Setting the programmer base time ...............114
4.19.16. ENERG - Enabling the energy counter function.......114
4.19.17. T.SAMP - Main input sample time ...........................114
4.19.18. FREQZ - Defining power line frequency ..................114
4.20. TIMER Submenu – Configuring timer parameters .............115
4.20.1. F.tiM - Selecting Timer function mode .....................116
4.20.2. St.St - Selecting the Start/Stop timer command ..... 116
4.20.3. S.S.t - Defining the Start/Stop timer command logic ....
116
4.20.4. rESE - Selecting the Reset timer command ............116
4.20.5. rES.t - Defining the timer reset command logic .......117
4.20.6. BAND - Band for timer count ...................................117
4.20.7. End - Selecting the function activated at end of count .
117
4.20.8. TIMER - Timer value ...............................................117
4.20.9. MSG.TM - Selecting the message assigned to the
active count .............................................................118
4.21. ENERG Submenu - Configuring energy counter parameters ..
119
4.21.1. ENERG - Selecting the output for energy calculation ....
120
4.21.2. V.LINE - Nominal line voltage ...................................120
4.21.3. P.LOAD - Nominal power of load ............................. 120
4.21.4. E.COST - Nominal cost per kWh .............................120
4.22. SERIA Submenu – Configuring serial communication ....... 121
4.22.1. CODE - Identification code ...................................... 122
4.22.2. KBAUD - Selecting communication speed ..............122
4.22.3. PAr - Selecting parity ...............................................122
4.23. HMI Submenu – Configuring the display and keypad .......123
4.23.1. but.1 - Selecting function key 1 ............................... 124
4.23.2. but.2 - Selecting function key 2 .............................. 124
4.23.3. but.3 - Selecting function key 3 .............................. 124
4.23.4. dS.SP - Selecting the SV display .............................125
4.23.5. dS.F - Selecting the F display ..................................125
4.23.6. bArG - Selecting the bargraph display ....................125
4.23.7. MSG.LO - Selecting the message assigned to Low 126
4.23.8. MSG.HI - Selecting the message assigned to HIGH .....
126
4.23.9. MSG.ER - Selecting the message assigned to Err .126
4.23.10. MSG.SB - Selecting the message assigned to Sbr . 127
4.23.11. LAnG - Selecting language for messages ...............127
4.23.12. SPEED - Message scrolling speed ..........................127
4.23.13. BACKL - Backlighting level ......................................127
4.23.14. QUICK - Quick configuration menu .........................128
4.24. LINRZ Submenu – Configuring custom linearization .........129
4.24.1. STP.xx - Value of step xx .........................................130
4.24.2. MV.STA - Setting mV at start of scale ...................... 130
4.24.3. MV.FUL - Setting mV at full scale ............................130
4.24.4. MV.50C - Setting mV at temperature of 50 °C ......... 130
4.25. US.CAL Submenu – User calibrations ...............................131
4.25.1. U.CAL - Selecting the user calibration .....................132
4.25.2. FI.CAL - Resetting the factory calibration ................132
4.25.3. C.LOW - Calibrating minimum current / voltage ......132
4.25.4. C.HIGH - Calibrating maximum current / voltage .... 133
4.25.5. RTD.LO - Calibrating minimum resistance value .....133
4.25.6. RTD.HI - Calibrating maximum resistance value .....133
4.25.7. HOUR - Setting hours .............................................. 133
4.25.8. MIN - Setting minutes .............................................. 133
4.25.9. SEC - Setting seconds .............................................134
4.25.10. dAY - Setting day of week .......................................134
4.25.11. DATE - Setting day ...................................................134
4.25.12. Mont - Setting month ...............................................134
4.25.13. YEAR - Setting year .................................................134
4.25.14. C.LO - Setting analog output minimum ................... 135
4.25.15. C.HIG - Setting analog output maximum ................135
4.26. PASC1 - Setting level 1 password 1 ..................................136
4.27. PASC2 - Setting level 2 password 2 ..................................136
4.28. FI.CFG - Entering the reset code .......................................136
5. Examples and application notes .........................137
5.1. Heat/cool control application ............................................. 137
5.1.1. Connection diagram.................................................137
5.1.2. Quick configuration procedure for model 650–D-R00-
00000-1 ....................................................................138
5.2. Heating control and current (CT) application .....................139
5.2.1. Connection diagram.................................................139
5.2.2. Quick configuration procedure for model 650-D-R00-
00100-1 ....................................................................140
5.3. Remote setpoint input ........................................................141
5.4. 4-point input correction ......................................................141
5.5. Current inputs ....................................................................141
5.6. Alarms ................................................................................142
5.6.1. Generic alarms AL1...AL4 .......................................142
5.6.2. HB alarm ..................................................................143
5.6.3. LBA alarm ................................................................143
5.7. Retransmission output .......................................................144
5.8. Switching the software on/off ............................................144
5.8.1. How to switch it off ..................................................144
5.8.2. How to switch it on ..................................................144
5.9. Soft-Start ............................................................................144
5.10. Tuning .................................................................................144
5.10.1. Tuning actions .......................................................... 144
5.10.1.1. Influence of Proportional, Derivative and Integral actions on
response of controlled process ....................................... 144
5.10.2. Manual tuning ..........................................................144
5.10.3. Self-Tuning ...............................................................145
5.10.4. Auto-Tuning ..............................................................146
5.10.5. Examples of tuning ..................................................146
5.10.6. Heat/Cool tuning with relative gain .......................... 146
5.11. Timer ..................................................................................147
5.11.1. Start/Stop Timer.......................................................147
5.11.2. Stabilization timer ....................................................148
5.11.3. Start timer ................................................................148
5.11.4. Variables available for the user configuration menu 148
5.12. Multiset, setpoint gradient .................................................149
5.13. Setpoint programmer .........................................................149
CONTENTS