Getidy JN-23 - Maintenance and Troubleshooting; Safety Warnings for Maintenance; Routine Cleaning and Upkeep

59 pages

Save Page as PDF

To Next Page

To Previous Page

6.2 Routine Maintenance

6.Maintenance

6.1 Safety warnnings

Page 38 of 58

--Observe the intervals prescribed or shown in this manual.Activates menorandum messages to assist the users to performing

Main Page

Table of Contents2
User Report4
User Notice4
Manual Guide4
Security Notice5
Safety Devices7
Electrical Safety7
Thermal Protection7
Mechanical Safety Devices8
Control Devices8
Summary & Suitable Using Range9
Technical Parameter9
- JN-23 Overall Space Required10
- Rating Plate11
- Usable Space 23 Litres11
- External Printer12
- Noise Level12
- Work Environment13
- Positioning13
Installation13
- JN-23 Steam Sterilizer Function and Operation Instruction17
- Operator Interface Introduction17
- Main Interface17
- Sterilization Program17
- Warning Icon Introduction18
- Door Status18
- Water Status18
- “SET up 1” Introduction19
- Calibration20
- Date and Time20
- User Information20
- Language20
- Preference21
- Sleepmode21
- Delay Start21
- Power Saving22
- Service22
- Maintenance Infor22
- Pipeline Cleaning23
- System Test23
- Alarm Codes23
- System Information24
- Label Printer24
- Auto-Water Supply24
- “SET up 2” Introduction24
- USB Record26
- Download the Current a Record26
- Download All the Records26
- MIN-Printer External Printer26
- “Abnormally Exit” Function27
- Sterilization Program List28
Steam Sterilization Program Introduction28
- Each Sterilization Phase Diagram29
- Three Pre-Vacuum Sterilization Program Process Schematic30
- Run Sterilization Program31
- Three Times Pre-Vacuum Program31
- The First Times Pre-Vacuum Stage31
- The First Times Heating Stage31
- The Start Sterilization Stage32
- The Three Times Pre-Vacuum Stage32
- The Three Times Heating Stage32
- The Second Times Exhaust Stage32
- After Sterilization Exhaust Stage33
- Drying Stage33
- Balance Atmospheric Stage33
- Sterilization Record Print Stage33
- One Times Pre-Vacuum Program34
- The First Times Exhaust Stage34
- The Second Times Heating Stage34
- User-Definned Program36
- Pre-Vacuum Program36
- Test Program37
- Maintenance39
- Safety Warnings39
- Routine Maintenance39
- Maintenance Programme40
- Sterilization Chamber40
- Seal and Door41
- Emptying and Cleaning the Tanks42
- Periodic Maintenance43
- Servicing the Safety Valve43
- Adjusting the Closing Mechanism43
- Resetting the Safety Thermostat44
- Extraordinary Maintenance44
- Service Maintenance44
- Replacing the Air Filter45
- Replacing the Door Sealing45
- Cleaning the Draining Water Filter45
- Power Fuse45
- Resale46
- Scraping Instructions46
Scraping46
APPENDIX 1:Preparing the Instruments for Sterilization46
Packaging47
APPENDIX 2:Packing47
APPENDIX 3:Positioning the Load48
Vacuum Test50
APPENDIX 4:Description of Tests50
- Bowie & Dick Test51
- Helix Text51
- Pre-Heating51
APPENDIX 5:Validating the Cycles52
APPENDIX 6:Quality of Process Water53
APPENDIX 7:Jn-23 Steam Sterilizer Hydraulic Circuit54
- Power Filter55
- Power Switch55
APPENDIX 8:Circuit Diagram of JN-23 Steam Sterilizer55
- E 0056
- E 9856
- E 0156
APPENDIX 9:Alarm Code and Solutions of JN-23 Steam Sterilizer56
- E 0457
- E 0557
- E 0657
- E 0757
- E 1158
- E 1258
APPENDIX 10:Accessories58

Getidy JN-23 - Maintenance and Troubleshooting; Safety Warnings for Maintenance; Routine Cleaning and Upkeep

Table of Contents

Related product manuals