Getidy JN-23 - Replacing the Air Filter; Replacing the Door Sealing; Cleaning the Draining Water Filter; Power Fuse

59 pages

Save Page as PDF

To Next Page

To Previous Page

6.3.1 Rusting

The fuse on the internal card is of the type:

5X20-10A(AC 230V/50Hz/60Hz);5X20-20A(AC 110V/60Hz)

Fig.6.3-1

solenoid valve.(Fig.6.3-1)

Page 44 of 58

Main Page

Table of Contents2
User Report4
User Notice4
Manual Guide4
Security Notice5
Safety Devices7
Electrical Safety7
Thermal Protection7
Mechanical Safety Devices8
Control Devices8
Summary & Suitable Using Range9
Technical Parameter9
- JN-23 Overall Space Required10
- Rating Plate11
- Usable Space 23 Litres11
- External Printer12
- Noise Level12
- Work Environment13
- Positioning13
Installation13
- JN-23 Steam Sterilizer Function and Operation Instruction17
- Operator Interface Introduction17
- Main Interface17
- Sterilization Program17
- Warning Icon Introduction18
- Door Status18
- Water Status18
- “SET up 1” Introduction19
- Calibration20
- Date and Time20
- User Information20
- Language20
- Preference21
- Sleepmode21
- Delay Start21
- Power Saving22
- Service22
- Maintenance Infor22
- Pipeline Cleaning23
- System Test23
- Alarm Codes23
- System Information24
- Label Printer24
- Auto-Water Supply24
- “SET up 2” Introduction24
- USB Record26
- Download the Current a Record26
- Download All the Records26
- MIN-Printer External Printer26
- “Abnormally Exit” Function27
- Sterilization Program List28
Steam Sterilization Program Introduction28
- Each Sterilization Phase Diagram29
- Three Pre-Vacuum Sterilization Program Process Schematic30
- Run Sterilization Program31
- Three Times Pre-Vacuum Program31
- The First Times Pre-Vacuum Stage31
- The First Times Heating Stage31
- The Start Sterilization Stage32
- The Three Times Pre-Vacuum Stage32
- The Three Times Heating Stage32
- The Second Times Exhaust Stage32
- After Sterilization Exhaust Stage33
- Drying Stage33
- Balance Atmospheric Stage33
- Sterilization Record Print Stage33
- One Times Pre-Vacuum Program34
- The First Times Exhaust Stage34
- The Second Times Heating Stage34
- User-Definned Program36
- Pre-Vacuum Program36
- Test Program37
- Maintenance39
- Safety Warnings39
- Routine Maintenance39
- Maintenance Programme40
- Sterilization Chamber40
- Seal and Door41
- Emptying and Cleaning the Tanks42
- Periodic Maintenance43
- Servicing the Safety Valve43
- Adjusting the Closing Mechanism43
- Resetting the Safety Thermostat44
- Extraordinary Maintenance44
- Service Maintenance44
- Replacing the Air Filter45
- Replacing the Door Sealing45
- Cleaning the Draining Water Filter45
- Power Fuse45
- Resale46
- Scraping Instructions46
Scraping46
APPENDIX 1:Preparing the Instruments for Sterilization46
Packaging47
APPENDIX 2:Packing47
APPENDIX 3:Positioning the Load48
Vacuum Test50
APPENDIX 4:Description of Tests50
- Bowie & Dick Test51
- Helix Text51
- Pre-Heating51
APPENDIX 5:Validating the Cycles52
APPENDIX 6:Quality of Process Water53
APPENDIX 7:Jn-23 Steam Sterilizer Hydraulic Circuit54
- Power Filter55
- Power Switch55
APPENDIX 8:Circuit Diagram of JN-23 Steam Sterilizer55
- E 0056
- E 9856
- E 0156
APPENDIX 9:Alarm Code and Solutions of JN-23 Steam Sterilizer56
- E 0457
- E 0557
- E 0657
- E 0757
- E 1158
- E 1258
APPENDIX 10:Accessories58

Getidy JN-23 - Replacing the Air Filter; Replacing the Door Sealing; Cleaning the Draining Water Filter; Power Fuse

Table of Contents

Related product manuals