Why is the red status lamp flashing rapidly on the HellermannTyton Power Tool?
If the red status lamp is flashing rapidly, it indicates the organiser unit is blocked. Open the organiser unit, remove the blockage, and then close the organiser unit.
Why does the HellermannTyton Power Tool stop without finishing the embossing job, and the status lamp is red?
If the device stops without finishing the embossing job and the status lamp is red, it's because the organiser unit was not reset before the embossing job. Open the organiser unit, empty any filled boxes, and then close the organiser unit.
What to do if the embossing is crooked with the HellermannTyton Power Tool?
If the embossing is crooked, it could be due to several reasons: the markers are crooked in the gripper, the marker is hard to pull out, or the gripper does not close properly. Check the marker for damage, adjust the gripper, and rotate the material by 180° or change it if necessary.
What to do if the HellermannTyton Power Tool displays 'Cover open'?
If the HellermannTyton Power Tool displays 'Cover open', it means the folding cover is not closed properly. Close the folding cover.
Why are the markers upright in the magazine of the HellermannTyton Power Tool?
If the markers are upright in the magazine, it's likely due to a low number of pieces, causing the markers to run without weight. Refill the magazine and insert weight.
Details the intended use and scope of the M-BOSS Compact system.
Explains various labels and symbols used throughout the manual for clarity.
Instructions on how to store and maintain the operating instructions.
States the device's compliance with relevant EU directives.
Describes how warning instructions are structured and their meaning.
Explains the severity levels of warnings (DANGER, WARNING, CAUTION, NOTE).
Defines the proper application and purpose of the M-BOSS Compact system.
Lists prohibited uses of the device and potential liabilities.
Details the safety mechanisms integrated into the device.
General safety guidelines for operating the device, including electrical and injury risks.
Specifies environmental and operational constraints for using the device.
Outlines the necessary qualifications and training for operators.
Lists the responsibilities of the device operator.
Identifies the main components of the M-BOSS Compact device from different views.
Describes the organiser unit's function and capacity for storing markers.
Details the drawer insert's role in holding embossed markers and unused materials.
Explains the different types and capacities of marker magazines.
Provides information on the material, properties, and specifications of the markers.
Identifies and explains the function of various control elements and indicators.
Describes the overall function of the device and its interaction with software and accessories.
Instructions on how to properly position the device for operation.
Steps for connecting the device to power and a PC via USB.
Overview of the software installation process, including downloading files.
Step-by-step guide for installing the necessary device drivers.
Procedures for integrating the device into the PC's operating system.
Instructions for installing the Metal Printer Monitor application.
Guide on how to download and install the TagPrint Pro software.
Steps to power on the device and start the Metal Printer Monitor.
Procedures for correctly filling and inserting marker magazines.
Detailed steps for creating a single embossed marker using TagPrint Pro.
Guide on how to perform serial embossing using the TagPrint Pro software.
Instructions on how to safely remove embossed markers from the device.
Steps to safely empty the drawer containing embossed markers.
Procedures for emptying the organiser unit after operation.
Common errors related to markers and their solutions.
Identifies device-specific errors and provides troubleshooting steps.
Lists potential software-related issues and their resolutions.
Addresses errors specific to the organiser unit's operation.
Essential steps to take before and after performing servicing work.
Defines the maintenance tasks to be performed at different intervals.
Lists the recommended cleaning agents and materials for maintenance.
Steps for cleaning optical sensors and light barriers.
Instructions for cleaning and lubricating the device's guide rods.
Procedures for cleaning the internal working area and the marker drawer.
How to clean the external casing of the device.
Steps for cleaning the interior surface of the folding cover.
How to adjust the gripper for correct marker positioning.
Procedures for addressing issues with the embossing drum.
Steps for safely replacing the device's power input fuse.
Instructions for safely shutting down and disconnecting the device.
Steps to follow when reconnecting and restarting the device.
Technical specifications for the M-BOSS Compact system.
Technical details and dimensions of the stainless steel markers.
General| Material | Steel |
|---|---|
| Method of Printing | Embossing |
| Type | Manual |
| Power Supply | Manual |
| Marking Material | Stainless Steel, Aluminum |
| Label Width | 6mm, 9mm, 12mm |
| Character Set | Alphanumeric and symbols |
To Next Page