Holtek HT66F002 - D.C. Characteristics

Rev. 1.71 14 April 11, 2017 Rev. 1.71 15 April 11, 2017
HT66F002/HT66F0025/HT66F003/HT66F004
Cost-Effective A/D Flash MCU with EEPROM
HT66F002/HT66F0025/HT66F003/HT66F004
Cost-Effective A/D Flash MCU with EEPROM
D.C. Characteristics
Ta = 25°C
Symbol Parameter
Test Conditions
Min. Typ. Max. Unit
V
DD
Conditions
V
DD
Operating Voltage (HIRC) — f
SYS
=8MHz 2.2 — 5.5 V
I
DD1
Operating Current,
Normal Mode, f
SYS
=f
H
(HIRC)
3V
No load, f
H
=8MHz, ADC off,
WDT enable, LVR enable
— 1.0 2.0 mA
5V — 2.0 3.0 mA
I
DD2
Operating Current,
Slow Mode, f
SYS
=f
L
=LIRC
3V
No load, f
SYS
=LIRC, ADC off,
WDT enable , LVR enable
— 20 30 μA
5V — 30 60 μA
I
DD3
Operating Current,
Normal Mode, f
H
=8MHz (HIRC)
3V
No load, f
SYS
=f
H
/2, ADC off,
WDT enable, LVR enable
— 1.0 1.5 mA
5V — 1.5 2.0 mA
3V
No load, f
SYS
=f
H
/4, ADC off,
WDT enable, LVR enable
— 0.9 1.3 mA
5V — 1.3 1.8 mA
3V
No load, f
SYS
=f
H
/8, ADC off,
WDT enable, LVR enable
— 0.8 1.1 mA
5V — 1.1 1.6 mA
3V
No load, f
SYS
=f
H
/16, ADC off,
WDT enable, LVR enable
— 0.7 1.0 mA
5V — 1.0 1.4 mA
3V
No load, f
SYS
=f
H
/32, ADC off,
WDT enable, LVR enable
— 0.6 0.9 mA
5V — 0.9 1.2 mA
3V
No load, f
SYS
=f
H
/64, ADC off,
WDT enable, LVR enable
— 0.5 0.8 mA
5V — 0.8 1.1 mA
I
IDLE0
IDLE0 Mode Standby Current
(LIRC on)
3V
No load, ADC off, WDT enable,
LVR disable
— 1.3 3.0 μA
5V — 5.0 10 μA
I
IDLE1
IDLE1 Mode Standby Current
(HIRC)
3V
No load, ADC off, WDT enable,
f
SYS
=8MHz on
— 0.8 1.6 mA
5V — 1.0 2.0 mA
I
SLEEP0
SLEEP0 Mode Standby Current
(LIRC off)
3V
No load, ADC off, WDT disable,
LVR disable
— 0.1 1.0 μA
5V — 0.3 2.0 μA
I
SLEEP1
SLEEP1 Mode Standby Current
(LIRC on)
3V
No load, ADC off, WDT enable,
LVR disable
— 1.3 5.0 μA
5V — 2.2 10 μA
V
IL1
Input Low Voltage for I/O Ports or
Input Pins except RES pin
5V — 0 — 1.5 V
— — 0 — 0.2V
DD
V
V
IH1
Input High Voltage for I/O Ports or
Input Pins except RES pin
5V — 3.5 — 5.0 V
— — 0.8V
DD
— V
DD
V
V
IL2
Input Low Voltage (RES) — — 0 — 0.4V
DD
V
V
IH2
Input High Voltage (RES) — — 0.9V
DD
— V
DD
V
I
OL
I/O Port Sink Current
3V V
OL
=0.1V
DD
18 36 — mA
5V V
OL
=0.1V
DD
40 80 — mA
I
OH
I/O Port, Source Current
3V V
OH
=0.9V
DD
-3 -6 — mA
5V V
OH
=0.9V
DD
-7 -14 — mA
R
PH
Pull-high Resistance for I/O Ports
3V — 20 60 100 kΩ
5V — 10 30 50 kΩ
I
OCDS
Operating Current, Normal Mode,
f
SYS
=f
H
(HIRC) (for OCDS EV
testing, connect to an e-Link)
3V
No load, f
H
=8MHz, ADC off,
WDT enable
— 1.4 2.0 mA