Honeywell NOTIFIER UDACT

To Next Page

To Previous Page

UDACT Instruction Manual — P/N 50050:M 12/18/2009 121

Index W–Z

wiring

entering

exiting

nonpower-limited

power limited

Relay Driver

zone 32, 56, 59

zone number

zone reporting

zone trouble

Main Page

Table of Contents5
Section 1: Overview9
Introduction9
UL 864 Compliance9
1: Products Subject to AHJ Approval9
2: Programming Features Subject to AHJ Approval9
Related Documentation10
Description10
Features10
Controls and Indicators11
Compatible Panels12
Digital Communicator12
Circuits12
1: Communications12
2: Primary and Secondary Phone Lines13
3: Communicator Fail Relay Driver13
4: Earth Ground13
Specifications13
1: DC Power13
2: Data Communications13
3: Auxiliary Output13
Telephone Requirements and Warnings13
1: Telephone Circuitry14
2: Digital Communicator14
3: Telephone Company Rights and Warnings14
4: for Canadian Applications15
Modes and Special Functions15
1: Normal Mode15
2: Program Mode16
3: Type Mode16
4: Troubleshoot Mode16
5: Lamp Test Mode16
6: Clear Function16
7: Manual Test Function16
Section 2: Installation and Wiring17
Installation17
1: Options17
Power Connection - 24 VDC23
Communication Connection23
Telephone Connections24
Relay Driver (Auxiliary Output) Connections25
UL Power-Limited Wiring Requirements27
Section 3: Programming Instructions28
General28
Entering Programming Mode28
Switch Functions29
Programming Options29
1: Primary Number Communication Format (16)30
2: Primary Number Account Code (17-20)31
3: Primary Number 24 Hour Test Time (21-24)31
4: Primary Number 24/12 Hour Test Time Interval (25)31
5: Secondary Phone Number (26-41)31
6: Secondary Number Communication Format (42)31
7: Secondary Number Account Code (43-46)32
8: Secondary Number 24-Hour Test Time (47-50)32
9: Secondary Number 24/12 Hour Test Time (51)32
10: Start Monitoring Address (52-53)32
11: End Monitoring Address (54-55)32
12: UDACT Communication Selection (56)33
13: Backup Reporting (57)34
14: Touchtone/Rotary Select (58)34
15: Make Break Ratio (59)34
16: Address (60)34
17: Address (61)34
18: AC Loss Reporting Delay (62)34
19: Host Panel ID (63)34
20: Loop Number (64 - 65)35
21: Device/Zone Number (66 - 68)35
22: Programming Event Codes (69-208)35
23: Programming the Real-Time Clock36
24: End Programming36
3+1, 4+1 Express and 4+1 Standard Formats37
1: Primary Number37
2: Secondary Number38
4+2 Standard and 4+2 Express Formats39
1: Primary Number39
2: Secondary Number40
Ademco Contact ID Format41
1: Primary Number41
2: Secondary Number42
Programming Reference Sheets43
1: Options43
2: Event Codes45
Factory Default Settings46
Section 4: Operating Instructions48
Normal Mode48
1: Function Keys48
2: Displays and Leds49
3: Normal Mode Operation50
4: Key Report Descriptions52
Type Mode52
1: Disabling of Zones or Points54
2: Zone or Point Supervisory54
Troubleshoot Mode54
1: Telephone Line Testing54
Lamp Test Mode55
Section 5: Reporting Formats56
Data Reporting Structure56
1: Ademco Contact ID58
Section 6: Compatible Receivers61
UL Listed Receivers61
Appendix A: AFP-100 (UL 8Th)63
A.1: General63
A.2: Mounting63
A.2.1: Internal63
A.2.2: Remote64
A.3: Wiring64
A.3.1: Connections64
A.3.2: Notes64
A.4: Zone Assignments66
A.5: Point Assignments67
Appendix B: AFP-200 (UL 8Th)68
B.1: General68
B.2: Mounting68
B.3: Wiring68
B.3.1: Connections68
B.3.2: Notes68
B.4: Zone Assignments70
Appendix C: System 500 (UL 8Th)71
C.1: General71
C.2: Mounting71
C.3: Wiring71
C.3.1: Connections71
C.3.2: Notes71
C.4: Zone Assignments73
Appendix D: System 5000 (UL 8Th)74
D.1: General74
D.2: Module Slot Position74
D.3: Mounting75
D.4: Wiring75
D.4.1: Connections75
D.4.2: Notes75
D.5: Zone Assignments with AIM-20077
D.6: Zone Assignments Without AIM-20079
Appendix E: AFP-300 & AFP-400 (UL 8Th)80
E.1: General80
E.1.1: Afp-30080
E.1.2: Afp-40080
E.2: Mounting80
E.3: Wiring80
E.3.1: Connections80
E.3.2: Notes80
E.4: Type Mode Programming82
E.4.1: for Zone Identification82
E.4.2: for Point Identification82
E.5: Event Code/Report Transmission83
E.5.1: for Zone Reporting83
E.5.2: for Point Reporting83
E.6: Zone Assignments84
E.7: Point Assignments85
Appendix F: NFS2-640, NFS-320, (UL 9Th) and NFS-640 (UL 8Th)88
F.1: General88
F.2: Mounting88
F.3: Wiring88
F.3.1: Connections88
F.3.2: Notes89
F.4: Type Mode Programming91
F.4.1: for Zone Identification91
F.4.2: for Point Identification91
F.5: Event Code/Report Transmission92
F.5.1: for Zone Reporting92
F.5.2: for Point Reporting92
F.6: Zone Assignments93
F.7: Point Assignments94
Appendix G: NCA-2 (UL 9Th) and NCA (UL 8Th)100
G.1: General100
G.2: Mounting100
G.3: Wiring100
G.3.1: Connections100
G.3.2: Notes100
Appendix H: AM2020/AFP1010 (UL 8Th)103
H.1: General103
H.2: Mounting103
H.3: Wiring103
H.3.1: Connections103
H.3.2: Notes104
H.4: Point Assignments105
Appendix I: NFS2-3030 (UL 9Th) and NFS-3030 (UL 8Th)109
I.1: General109
I.2: Mounting109
I.2.1: Wiring109
I.2.2: Connections109
I.2.3: Notes109
I.3: Point Assignments112
Appendix J: Annunciators115
J.1: General115
J.1.1: AFP-100, AFP-200, and AFP-300/AFP-400115
J.1.2: System 500 & System 5000115
J.1.3: Am2020/Afp1010116
Index117

Honeywell NOTIFIER UDACT - Page 121

Table of Contents

Related product manuals