Honeywell SPM Flex - User Manual

SPM Flex
Single Point Monitor Gas Detector
User Manual

Honeywell SPM Flex Specifications

General

Brand	Honeywell
Model	SPM Flex
Category	Security Sensors
Language	English

Summary

Introduction

Safety Information

Contact Information

Glossary

Product Overview

Fixed Detectors

Details on fixed installation configuration and components.

Additional Accessories

Lists optional accessories for detector enhancement and functionality.

Wiring and Tubing

Typical Fixed Installation Topologies

Describes common wiring configurations for fixed detector installations.

Ethernet Connector and Terminal Module

Details the Ethernet port and the internal terminal module for connections.

Wiring Diagrams

Illustrates various wiring diagrams for different configurations, including 4-20 mA.

4-20 mA Wiring

Explains the three-wire connection for 4-20 mA output, including sink, source, and isolated.

Relays and Modbus

Covers relay configuration and Modbus/TCP server capabilities for data communication.

Modbus Register Definitions

Provides a detailed table of Modbus register addresses, bits, descriptions, and values.

Tubing (Optional)

Details sample and exhaust tubing specifications and calculations for optimal performance.

Setup

Installation Drawing

Provides technical drawings for detector installation, including dimensions and mounting.

Dimensions

Details the physical dimensions of the SPM Flex detector in inches and centimeters.

Mounting Options

Describes available mounting bracket options for fixed detector installations.

Standard Mounting Bracket

Illustrates the standard mounting bracket and its installation dimensions.

Backward-Compatible Mounting Bracket

Details the mounting bracket for replacing older SPM detector models.

Sun Shield

Describes the sun shield for outdoor applications, protecting the detector from elements.

Flip-Screen Function

Explains how to rotate the display for optimal viewing in different installation orientations.

Converting Fixed to Portable

Procedure for converting a fixed installation detector into a portable unit.

In-line Filters

Discusses the importance and types of in-line filters for detector protection.

Optional Sampling Wand

Details the use and limitations of the optional sampling wand for specific gas detection.

Operation

Power Operation

Covers power-up sequence, battery status, and powering the detector off.

Controls

Explains the use of control buttons for menu navigation and operation.

Time, Audible Alarm, and Monitoring Icons

Details the real-time clock, audible alarm settings, and status monitoring icons.

Battery and Bar Graph

Describes how battery level and gas concentration are displayed on the detector.

Inhibit Functionality

Details how to enable or disable alarms and faults for specific periods.

Review Menu Options

Covers accessing event history, Chemcassette details, and gas settings.

Network and Additional Status

Details network summary and additional status information like flow rate and battery.

Software and Maintenance Menu

Covers software versions and access to the maintenance menu functions.

Flow Characterization and Setup

Explains flow optimization and general setup configurations for the detector.

Monitoring and Latching

Discusses gas monitoring settings, latching options, and alarm volume.

Network Configuration

Describes how to enable and configure Ethernet connection and Modbus TCP.

Security Features

Details the detector's security levels and access rights based on passcodes.

Configuration, Testing, and Duty Cycle

Covers configuration manager, test menu options, and duty cycle settings.

K-Factor and Stale Tape Features

Explains gas cross-sensitivity adjustment and stale tape fault management.

Troubleshooting

Troubleshooting Common Issues

Provides a table of symptoms, causes, and corrective actions for common detector problems.

Instrument and Maintenance Fault Codes

Lists and explains various instrument and maintenance fault codes.

Maintenance

Maintenance Schedule and Preventive Maintenance

Outlines recommended maintenance intervals and authorized service recommendations.

Replacing the End-of-Line Filter

Step-by-step guide for replacing the end-of-line filter.

Checking Pump and Optic System

Procedures for checking pump functionality and verifying optic system response.

Replacing Internal Filters

Instructions for removing and replacing internal dust and acid scrubber filters.

Replacing the Pump

Detailed procedure for replacing the detector's pump assembly.

Checking Stepper and Gate Motors

Guidance on diagnosing and resolving stepper and gate motor malfunctions.

Replacing Real-Time Battery and Cleaning Surfaces

Instructions for battery replacement and cleaning exterior surfaces.

Cleaning Tape-Contact Surfaces

Procedures for cleaning tape transport surfaces to prevent false readings.

Checking for System Leaks

Methods for verifying the integrity of tubing connections and detecting system leaks.

Detector Storage and Recycling

Guidelines for proper storage of the detector and end-of-life recycling.

Certifications

Warranties