HP 5300A - Ordering Information

pecs
Model 5300A
Replaceable Parts
SECTION VI
REPLACEABLE PARTS
6-1. INTRODUCTION
6-2. This section contains information for ordering
replacement parts. Tables 6-1, 6-2, and 6-3 list parts
used in the HP 5300A, 5310A, and 10533A respec-
tively. The table lists parts in alphanumeric order
of their reference designations and provides the fol-
lowing information on each part:
a. Hewlett-Packard part number.
b. Description of part (see abbreviations below).
c. Total quantity used in the instrument (the
first time that the part appears in the list, the total
quantity of that part number is printed).
d. Typical manufacturer of the part in a five-
digit. code (see list of manufacturers in Table 6-4).
e. Manufacturer’s part number.
-3. Miscellaneous parts are listed at the end of Table
6
6-1, 6-2, and 6-3.
6-4. ORDERING INFORMATION
6-4. To obtain replacement parts, address order or
inquiry to your local Hewlett-Packard Sales and
Service Office (see lists at rear of this Section for
addresses). Identify parts by their Hewlett-Packard
part number. To obtain a part that is not listed,
include:
a. Instrument model number.
b. Instrument serial number.
a
Description of the part.
Function and location of the part.
REFERENCE DESIGNATORS
fuse
filter
integrated circuit
jack
relay
inductor
loud speaker
meter
microphone
assembly
motor
battery
capacitor
coupler
diode
delay line
device signaling (lamp)
mise electronic part
rao oms
bh an
ZS x
MP - mechanical part
P > plug
Q transistor
R > resistor
RT thermistor
s - switch
T transformer crystal
TB terminal buard tuned cavity,
TP - test point network
integrated circuit
vacuum, tube, neon
bulb, photocell, etc.
voltage regulator
cable
socket
Nx eS <c
=5
ABBREVIATIONS
anipercs - henries
autumatic frequency contrul hardware
amplifier hexagonal
mercury
beat lrequency uscillator - hour{s)
beryllium copper hertz
binder head
bandpass 2 + intermediate freq
brass - impregnated
backward wave oscillator incandescent
include(s)
vounter-clockwise¢ insulation(ed)
ceranic internal
cabinet mount only kilo 1000
covfficicnt
conmunun - left hand
composition linear taper
complete luck washer
connector logarithmic taper
cadmium plate low pass filter
cathode-ray tube
clockwise milli - 1073
mep = 106
deposited carbon MET FLM metal film
drive MET OX metallic oxide
MFR ~- manufacturer
MHZ - mega hertz
MINAT - miniature
MOM momentary
farads MOS
flat head MTG
fillister head MY
fixed
siga (109) N
GE > germanium N’C
Clectrolytic
cenvapsulated
external
mounting
“mylar"
nano (10-9)
normally closed
GL - glass NE neon
GRD gruund(ed) NI PL nickel plate
O1194-14
metal ozide substrate
N/O > normally open RMO rack mount only
NOM numinal RMS root-mean square
NPO negative positive zeru RWV reverse working
(zero temperature voltage
NPN ee nines S=B ° slow-blow
SCR > screw
ncgative SE = selenium
NRFR > not recommended for SECT = section(s)
field: replacement SEMICON = semiconductor
NSR not separately ae
replaceable SI silicon
SIL silver
OBD > order by description SL slide
OH - oval head SPG spring
Ox oxide SPL : special
SST Stainless steel
PC - printed circuit ane ¥ oe
PF picofarads = 10-12 :
farads TA tantalum
phosphor bronze TD time delay
Phillips TGI >» toggle
peak inverse voltage THD - thread
positive-negative- TI . titanium
positive TOL > tolerance
part of TRIM trimmer
polystyrene TWT traveling wave tube
porcelain ee -6
position(s) U micro = 10
potentiometer VAR # variable
peak-to-peak vVDCW dc working volts
point
peak working voltage w/ > with
w watts
rectifier WIv working inverse
radiv frequency voltage
round head or ww = wirewound
right hand without
P - peak
6-1