HP 5300A - Manual Changes and Options

Model 5300A
Manual! Changes and Options
SECTION Vil
MANUAL CHANGES AND OPTIONS
7-1. MANUAL CHANGES
7-2. This manual applies directly to Model 5300A
Measuring Systems with serial number prefix 1320A,
to Model 5310A Battery Packs with serial number
prefix 1312A, and to Model 10533A Digital Recorder
Interfaces with circuit-board series number 1128A.
For information about manual changes for newer or
older units, refer to the following paragraphs.
7-3. Newer Instruments
7-4. As engineering changes are made, newer instru-
ments may have serial prefix numbers higher than
those listed on the title page of this manual. The
manuals for these instruments will be supplied with
‘manual changes” sheets containing the required
information. Replace affected pages or modify exist-
ing manual information as directed in the “manual
changes” pages. Contact the nearest Hewlett-
Packard Sales and Service Office if the change infor-
mation is missing.
7-5. Older Instruments
7-6. The following paragraphs list the manual
changes required to backdate this manual to cover
Model 5300A Measuring Systems and Model 5310A
Battery Packs with lower serial number prefixes than
those listed on the title page of this manual. Make the
manual changes given in the paragraph that corres-
ponds to the serial number prefix of your instrument.
7-7. 5300A, serial prefix 1312A: On the schematic
diagram and the component locator illustration of
Figure 8-2, delete AIR33 and the connection between
Ri, the SAMPLE RATE control, and the circuit com-
mon return line (ground). Delete A1R33 from the re-
placeable parts list of Table 6-1.
7-8. 5300A, serial prefix 1232A. Make the change
given in Paragraph 7-7. On Page 6-4, Table 6-1,
change the part number of the 60 integrated circuit
sockets (for Al1U1, 2, and 5) from “1200-0475” to
“1200-0464”.
7-9. 5300A, serial prefix 1208A. Make the changes
given in Paragraphs 7-7 and 7-8. On these and older’
instruments, two-piece catch-slides were used in
place of the newer one-piece parts listed on Page 6-4,
Table 6-1 (MP2 and MP9). The newer parts (part
numbers 5040-6000 and 5040-7001) should be used,
however, if replacement is required.
7-10. 5300A, serial prefix 1148A. Make the changes
given in Paragraphs 7-7 through 7-9. Delete
capacitor A2C7 from the schematic diagram and the
component locator illustration of Figure 8-2 and from
the replaceable parts list of Table 6-1.
7-11. 5300A, serial prefix 1104A. Makes the changes
given in Paragraphs 7-7 through 7-10. On Page 6-2,
Table 6-1, change the entry for A1C1 (part number
0150-0012) to the following: “A1C1, 0160-0153, 1,
C:FXD MY 0.001 UF 10% 200VDCW, 56289,
192P10292-PTS”. On the schematic diagram of Fig-
ure 8-2, change the value of A1C1 from “.0luF” to
“O01 uF”
7-12. 5310A, serial prefix 1232A. On Page 6-5, Table
6-2, delete the entries for MP8 and MP19; add the
following: “MP8, 05310-00003, 1, PANEL:SUB,
28480, 05310-00003”.
7-13. 5310A, serial prefix 1128A. Make the changes
given in Paragraph 7-12. On these and older instru-
ments two-piece catch-slides were used in place of
the newer one-piece parts listed on Page 6-5, Table
6-2 (MP4 and MP5). The newer parts (part numbers
5040-6000 and 5040-7001) should be used, however,
if replacement is required.
7-14. OPTIONS
7-15. No options available at time of printing.
7-1