Need help?Do you have a question about the HP 54 Basic Cutter and is the answer not in the manual?
Introduces the HP Latex Cutter's key features and capabilities.
Lists the different HP Latex Cutter models and their configurations.
Provides links and information on available user guides and support documents.
Outlines essential safety guidelines for using the cutter to prevent injury.
Identifies and describes the primary physical parts of the cutter.
Explains the procedure for powering the cutter on and off.
Details how to establish a connection between the cutter and a computer.
Describes the controls and display on the cutter's front panel interface.
Provides general safety rules for operating the cutter.
Warns about electrical hazards and necessary precautions.
Details precautions to prevent fire risks associated with the cutter.
Explains risks from moving parts and how to avoid injury.
Addresses potential hazards from LED light emissions.
Provides guidance on safely handling heavy substrate rolls.
Illustrates and identifies the primary physical parts of the cutter.
Explains symbols used for warnings and safety information in the manual.
Describes specific warning labels found on the cutter.
Shows a diagram of the cutter's front, labeling its parts.
Shows a diagram of the cutter's rear, labeling its parts.
Explains the procedure for powering the cutter on and off.
Details how to establish a connection between the cutter and a computer.
Describes how to connect the cutter to a computer using a LAN cable.
Provides instructions for connecting the cutter via USB.
Describes the controls and display on the cutter's front panel interface.
Lists website resources for HP Latex Cutter information and support.
Guides users on how to get support and what information to provide.
Provides step-by-step instructions for loading a substrate roll into the cutter.
Provides instructions for loading a substrate sheet into the cutter.
Explains how to correctly position the pinch rollers on the substrate.
Details how to calibrate the substrate for accurate sensor reading.
Guides on adjusting the knife depth and pressure for optimal cutting.
Explains how to adjust the cutter's speed and acceleration settings.
Details how to configure speed parameters independently.
Describes the process for calibrating the substrate length for accuracy.
Explains how to manage user profiles and their associated settings.
Introduces contour cutting and the role of the OPOS system.
Explains the function and components of HP barcodes for the OPOS sensor.
Discusses methods to automate cutting tasks for efficiency.
Details the OPOS origin parameter for automating job starts.
Explains how to use the HP barcode to retrieve cut data.
Describes different types of cutting jobs, like print-and-cut and direct-cut.
Explains the necessary calibrations for accurate OPOS operation.
Guides on how to set the cutter's origin point for cutting.
Explains the extended load function for cutting outside pinch rollers.
Describes the two main cut types: Kiss cut and Cut through.
Instructions for loading printed material for OPOS cutting.
Details how to manually adjust OPOS parameters.
Explains how to manually register markers for calibration.
Explains the cut-through functionality and its parameters.
Explains the panel settings for managing multiple cut sections.
Describes vector sorting options for optimizing cutting paths.
Lists the calibration types available for the cutter.
Overview of the chapter covering cutter parameters and tests.
Explains media alignment procedures for contour cutting.
Groups various operational settings for the cutter.
Lists available actions and tests that can be initiated from the cutter.
Details how to set and adjust pressure for different tools.
Explains how to set and check the knife offset for accuracy.
Describes how to set the gap for pouncing operations.
Explains the FlexCut feature for cutting through substrates.
How to change and set up different cutting tools.
Accessing cutter parameters and internal tests.
Lists available actions and tests that can be initiated from the cutter.
Explains media alignment procedures for contour cutting.
Groups various operational settings for the cutter.
Explains TurboCut for increased throughput and faster cutting.
Explains panel settings for managing multiple cut sections.
Describes vector sorting options for optimizing cutting paths.
Lists the calibration types available for the cutter.
Explains substrate calibration for sensor recognition of markers.
Guides on adjusting cut line lengths for specification adherence.
Details calibrating the distance between the OPOS sensor and knife tip.
Accessing and adjusting cutter configuration settings.
Displays and allows adjustment of the cutter's LAN settings.
Allows selection and changing of the front panel display language.
Determines display of speed and size values in metric or US units.
Displays the cutter's firmware version number for technical support.
Copies user settings to other user profiles.
Used to change various OPOS parameters from the front panel.
Restores all cutter parameters to their original factory settings.
Sets the USB class for cutter connection and driver installation.
Turns the substrate sensor on or off to detect substrate presence.
Selects alignment methods for contour cutting when markers are difficult to read.
Instructions for cleaning the cutter's sliding surfaces.
Details cleaning the drive drum sleeves to prevent substrate slippage.
Explains how to clean the substrate sensor for proper function.
Instructions for cleaning the Y-guide rail for smooth carriage movement.
Step-by-step guide to safely remove the drag knife.
Step-by-step guide to safely install a new drag knife.
How to set the knife offset after installation or wear.
Instructions for safely replacing the cutter's fuse.
Guides on updating the cutter's firmware using HP Cutter Control.
Solutions for issues related to poor cutting quality.
Addresses problems with substrate movement and tracking.
Provides solutions for when the substrate gets jammed.
Troubleshoots issues with the cutter not recognizing barcodes or marks.
Explains how to calibrate the OPOS sensor for accurate detection.
Lists available accessories and how to order them.
Guides on how to change and set the cutter's tool type.
Provides physical dimensions for the HP Latex Cutter models.
Details the dimensions of the cutter for shipping purposes.
Lists the width and roller specifications for substrates.
Specifies the maximum length of substrate the cutter can handle.
Defines the margins required at the front and rear of the substrate.
Specifies the required side margins for substrate loading.
Defines the spacing required between printed jobs.
Specifies the margin needed for the cut-off operation.
Details the cutter's tracking performance with different substrates.
Specifies the acceptable substrate thickness range for standard and optional knives.
Summarizes key performance metrics like cut type, speed, and accuracy.
Lists details about the cutter's firmware, including language and fonts.
Specifies operating and storage conditions for the cutter.
Details electrical specifications like voltage, frequency, and power.
To Next Page
General
