What to do if hpmont HD5L-4T011 Controller displays E0023 error?
If the hpmont Controller displays error E0023, which indicates a faulty setting of parameters, select a controller with a suitable power rating and set correct value of motor parameters.
What to do if hpmont HD5L-4T011 Controller displays E0025 error?
If the hpmont Controller displays error E0025, which indicates too small running current, correct the setting of F16.14, F16.15, check the connection between HD5L and motor, detect HD5L whether output and detect whether the output contactor work is normal.
Why hpmont HD5L-4T011 Controller shows E0018 error?
The E0018 error on the hpmont Controller indicates excessive speed deviation. To fix it, change the contactor, set proper PG P/R, correct the setting of F05.19 - F05.20, select bigger capacity, and correctly set speed-loop PI parameter.
How to troubleshoot DC bus undervoltage on hpmont Controller?
If you are experiencing DC bus undervoltage with your hpmont Controller, it could be due to normal power on/off cycling, low input voltage, or improper wiring. Check the input power voltage and ensure the controller is wired properly. Note that undervoltage can occur at the beginning of power on and at the end of power off, which is normal.
Why did the soft start fail on my hpmont Controller?
If the hpmont Controller indicates a 'Soft start failed' error, it could be due to a contactor fault or a fault in the control circuit. Replace the contactor.
What does Controlboard EEPROM faulty mean on hpmont HD5L-4T011?
If the hpmont Controller displays 'Controlboard EEPROM faulty', it means there is a memory circuit fault of control board EEPROM. Please contact the supplier for repairing.
What to do if hpmont Controller shows E0004 error?
If the hpmont Controller displays error E0004, which indicates Acc over voltage, you should check the power input, set a proper value for Dec time, and check wiring to ensure HD5L is wired properly.
What does Lu error mean on hpmont HD5L-4T011?
The Lu error on the hpmont Controller indicates DC bus undervoltage. This can be normal during power on and power off. Check the input power voltage and ensure the HD5L wiring is correct.
What to do if hpmont Controller displays E0019 error?
If the hpmont Controller displays error E0019, which indicates a motor overload, you can adjust the V/f curve, check the power input, properly set the overload protection factor of the motor, and check the load and mechanical transmission devices.
What to do if hpmont Controller displays E0017 error?
If the hpmont Controller displays error E0017, which indicates a controller overload, you can adjust the Acc time, adjust the V/f curve or torque boost, check the mains supply voltage, or use a controller with proper power rating.
General| Brand | hpmont |
|---|---|
| Model | HD5L-4T011 |
| Category | Controller |
| Language | English |
Provides guidelines for installing the controller to meet electromagnetic compatibility standards.
Introduces parameters for motor type, control mode, speed, frequency, and traction machine settings.
Covers fundamental parameters like motor type, control mode, rated speed, and operating mode.
Covers essential parameters for asynchronous motors, including rated power, voltage, current, and auto-tuning.
Covers parameters specific to synchronous motors, including type, voltage, current, and auto-tuning.
Details parameters for motor overheat, input/output phase loss, and motor overload protection.
Provides a step-by-step guide for system analysis, wiring, and parameter setup for elevator applications.
Explains the procedures for auto-tuning motors (asynchronous and synchronous) for optimal performance.
Explains how to apply the controller in terminal MS (multi-speed) run mode for elevator control.
Explains how to apply the controller in terminal analogue run mode for elevator control.
Describes the application of battery-driven run mode for emergency elevator operation during power outages.
Lists common fault codes, possible causes, and corresponding counter-measures for troubleshooting.
Covers fundamental parameters like motor type, control mode, rated speed, and operating mode.
Covers essential parameters for asynchronous motors, including rated power, voltage, current, and auto-tuning.
Details parameters for motor overheat, input/output phase loss, and motor overload protection.
To Next Page
