Icom IC-7410

87
SET MODE
10
4UNER0443TART17. $EFAULT/&&
Whenever you push [PTT], the internal or external an-
tenna tuner automatically starts tuning if the operating
FREQUENCYISCHANGEDBYMORETHANFROMTHELAST
tuned frequency.
s/&&4UNINGSTARTSONLYWHEN;45.%2=ISPUSHED
s/. )NTERNALANTENNATUNER4UNINGSTARTSWHEN
you push [PTT] on a new frequency, if the in-
ternal antenna tuner is ON.
(External antenna tuner) Tuning always starts
when you push [PTT] on a new frequency, re-
gardless of whether the external antenna tuner
is ON or OFF.
4UNER0RESET#LEAR18.
Select the desired antenna.
The selected antenna’s preset memory* is cleared by
holding down [CLR](F-4) for 1 second.
* The variable capacitor settings are memorized as a
preset point for each frequency range (100 kHz steps)
after the tuner matches an antenna.
s#,2!.44HEPRESETMEMORYOF;!.4=SANTENNA
is cleared.
s#,2!.44HEPRESETMEMORYOF;!.4=SANTENNA
is cleared.
;!.4=3WITCH19. $EFAULT!UTO
Set the antenna switch function to Auto, Manual or OFF.
When you change the operating frequency, this func-
tion will automatically select the correct antenna, or you
must do it manually.
s/&& ;!.4s-%4%2= DOES NOT FUNCTION 4HE
[ANT1] connector is always selected.
s-ANUAL 9OUMUSTMANUALLYCHANGETHEANTENNABY
PUSHING;!.4s-%4%2=
s!UTO 4HEANTENNAMEMORIZEDBYTHEBANDMEM-
ory is automatically selected. You can also
manually change the antenna by pushing
;!.4s-%4%2=
30%%#(,EVEL20. $EFAULT
!DJUSTTHESPEECHAUDIOOUTPUTLEVELTOBETWEEN
NOOUTPUTANDMAXIMUMOUTPUT
30%%#(,ANGUAGE21. $EFAULT%NGLISH
Select English or Japanese as the speech language.
30%%#(3PEED22. $EFAULT()'(
Select HIGH (faster) or LOW (slower) speech speed.
30%%#(3,EVEL23. $EFAULT/.
The signal level announcement with the voice synthe-
sizer can be turned ON or OFF.
s/&&4HESIGNALLEVELISNOTANNOUNCED/PERATING
frequency is announced.
s/. 4HESIGNALLEVELANDTHEOPERATINGFREQUENCY
are announced.
SPEECH [MODE] SW 24. $EFAULT/&&
Turn the Operating Mode Speech function ON or
OFF.
When this function is ON, the selected operating mode
is verbally announced when a mode switch is pushed.
s/&&4HEOPERATINGMODE3PEECHFUNCTIONIS/&&
s/. 4HEOPERATINGMODE3PEECHFUNCTIONIS/.
-EMOPAD.UMBERS25. $EFAULT
Set the number of available memo pads to 5 or 10.
See page 74 for details.
-!).$)!,!UTO4326. $EFAULT()'(
Set the Auto Tuning Step function for [DIAL]. When
rapidly rotating [DIAL], the tuning step automatically
changes as selected.
There are two types of auto tuning steps: LOW (Faster)
and HIGH (Fastest).
s/&& !UTOTUNINGSTEPISTURNED/&&
s,/7 !PPROXIMATELYTIMESFASTER
s()'(!PPROXIMATELYTIMESFASTERWHENTHETUNING
step is set to 1 kHz or smaller steps; approxi-
mately 2 times faster when the tuning step is
set to 5 kHz or larger steps.
N Set mode description (Continued)