Icom IC-7410

88
SET MODE
1
2
3
4
5
6
7
8
9
11
12
13
15
16
17
18
19
20
21
10
10
14
-)#5P$OWN3PEED27. $EFAULT()'(
Set the rate at which frequencies are scanned while
holding down the microphone [UP]/[DN] switches.
s,/7,OWSPEEDTUNINGSTEPSSECOND
s()'((IGHSPEEDTUNINGSTEPSSECOND
1UICK2)4#LEAR28. $EFAULT/&&
Select the RIT/∂TX frequency offset clearing opera-
tion with [CLEAR].
s/&&(OLDINGDOWN;#,%!2=FORSECONDCLEARSTHE
RIT and ∂TX frequency offset.
s/. 0USHING;#,%!2=INSTANTLYCLEARSTHE2)4AND
∂TX frequency offset.
;./4#(=3733" 29.
$EFAULT!UTO-ANUAL
Select the Auto, Manual or Auto/Manual notch filter to
be used for SSB mode operation.
s!UTO   Only the Auto notch filter can be used.
s-ANUAL  /NLY THE -ANUALNOTCH FILTER CANBE
used.
s!UTO-ANUAL"OTHTHE!UTOAND-ANUALNOTCHlLTERS
can be used.
;./4#(=37!- 30.
$EFAULT!UTO-ANUAL
Select the Auto, Manual or Auto/Manual notch filter
used for AM mode operation.
s!UTO  
Only the Auto notch filter can be used.
s-ANUAL  /NLY THE -ANUALNOTCH FILTER CANBE
used.
s!UTO-ANUAL"OTHTHE!UTOAND-ANUALNOTCHlLTERS
can be used.
-.10OPUP-./.31. $EFAULT/.
Turn the manual notch filter width display ON or OFF.
When this item set to ON, and the manual notch filter
is selected with [NOTCH], the manual notch filter width
appears on the function display.
"70OPUP0"432. $EFAULT/.
Turn the IF filter passband width and shift value dis-
play ON or OFF.
When this item set to ON, and the [TWIN PBT] control
is rotated, the passband width and shifting value ap-
pear on the function display.
"70OPUP&),33. $EFAULT/.
Turn the IF filter passband width and shift value dis-
play ON or OFF.
When this item set to ON, and [FILTER] is pushed,
the passband width and shifting value appear on the
function display.
33"#73YNC4UNING34. $EFAULT/&&
Turn the Displayed Frequency Shift function ON or
OFF.
When this function is turned ON, the audio pitch or
tones of the received signal will remain the same, even
when the operating mode is changed between SSB
and CW.
The amount of frequency shift may differ, depending
on the CW pitch setting.
s/&&4HEDISPLAYEDFREQUENCYDOESNOTSHIFT
s/. 4HEDISPLAYEDFREQUENCYSHIFTSWHENTHEOP-
erating mode is changed between SSB and
CW.
#7.ORMAL3IDE35. $EFAULT,3"
Select the sideband used to receive CW in the CW
normal mode between LSB and USB.
+%9%2ST-ENU36. $EFAULT+%9%22OOT
In the CW mode, select KEYER-Root or KEYER-
SEND as the menu that appears first after pushing
[KEY](F-4) in the “M1” screen (Menu 1).
s+%9%22OOT -EMORYKEYERMENUAPPEARSlRST
s+%9%23%.$+EYER3%.$MENUAPPEARSlRST
%XTERNAL+EYPAD37. $EFAULT/&&
Turn the external keypad ON or OFF for keyer mem-
ory transmission.
See page 18 for the equivalent circuit of an external
keypad and connection.
s/&& 4HEEXTERNALKEYPADDOESNOTFUNC-
tion.
s+%9%23%.$ )NTHE #7 MODEPUSHING ONE OF
external keypad switches transmits
the desired keyer memory con-
tents.