Icom IC-905 - Tone squelch operation

1-8
BASIC MANUAL
PANEL DESCRIPTION
1
1
Touch screen display
D Multi-function menus
z Open the Multi-function menu by pushing
(Multi-function control).
z Open special menus by holding down /
for 1 second.
z While the Multi-function menu is open, touch the
desired item and rotate to set the desired
value.
Multi-function menu items
*
1
Touch the item for 1 second to adjust by rotating
, even when the Multi-function menu is closed.
*
2
Touch the edge to turn the function ON or OFF, or to
adjust the selected item.
SSB SSB-D CW RTTY
RF POWER*
1
RF POWER*
1
RF POWER*
1
RF POWER*
1
MIC GAIN*
1
MIC GAIN*
1
KEY SPEED*
1
TPF*
2
COMP*
1
*
2
CW PITCH*
1
MONITOR*
1
*
2
MONITOR*
1
*
2
MONITOR*
1
*
2
FM/AM/DV DD ATV NB
RF POWER*
1
RF POWER*
1
RF POWER*
1
LEVEL*
1
MIC GAIN*
1
TX INHIBIT*
2
MIC GAIN*
1
DEPTH*
1
WIDTH*
1
MONITOR*
1
*
2
MONITOR*
1
*
2
MONITOR*
1
*
2
NR NOTCH VOX BK-IN
LEVEL*
1
POSITION*
1
GAIN*
1
DELAY*
1
WIDTH*
2
ANTI VOX*
1
DELAY*
1
VOICE DELAY*
2
TX PWR LIMIT
RF POWER*
1
LIMIT
Multi-function dial
When the Multi-function menu is closed, the
control can be enabled to adjust functions by pushing
or touching the item for 1 second on the Multi-
function menus.
The function is displayed in the upper right corner of
the screen.
*
3
Touch the function indicator or hold down for
1 second to assign the function to the
control,
when the RIT or ∂TX function is OFF.
*
4
On the Multi-function menus, touch the item for 1 second
to assign the function to the
control.
Indicator Action
RIT
Rotate Adjusts the RIT frequency.
Hold down Clears the RIT frequency.
∂TX
Rotate
Adjusts the ∂TX frequency.
Hold down
Clears the ∂TX frequency.
kHz*
3
Changes the operating frequency in kHz
steps. (VFO mode only)
MHz*
3
Changes the operating frequency in MHz
steps. (VFO mode only)
M-CH*
3
Selects Memory channels. (Memory mode
and Call channel mode only) When using
the DR function, selects an individual
station or preset repeater.
RF PWR*
4
Adjusts the transmit output power.
MIC G*
4
Adjusts the microphone gain.
COMP*
4
Adjusts the Speech Compressor level.
MONI*
4
Adjusts the audio level for the Monitor
function.
SPEED*
4
Adjusts the Keying speed.
PITCH*
4
Adjusts the CW pitch.
NB LEV*
4
Adjusts the Noise Blanker level.
NB DEP*
4
Adjusts the DEPTH (Noise attenuation
level).
NB WID*
4
Adjusts the WIDTH (Blanking duration
time).
NR LEV*
4
Adjusts the Noise Reduction level.
NOTCH*
4
AdjuststheNotchlterfrequency.
VOX G*
4
Adjusts the VOX gain.
A-VOX*
4
Adjusts the ANTI VOX level
VOX D*
4
Adjusts the VOX delay time.
BKIN D*
4
Adjusts the Break-in delay time.
Function indicator for
Touch the edge to
turn ON or OFF