135
Controlling Other Components
—Continued
The AV receiver’s remote controller can learn the com-
mands of other remote controllers. By transmitting, for
example, the Play command from your CD player’s
remote controller, the remote controller can learn it, and
then transmit the exact same command when its Play
[] button is pressed in the CD remote mode.
This is useful when you’ve entered the appropriate
remote control code (page 132) but some buttons don’t
work as expected.
Notes:
• The following buttons cannot learn new commands:
Remote Mode, Macro [1], [2], [3], TV [Input], TV CH
[+]/[–], TV VOL [ ]/[ ], [D.TUN], Light.
• The remote controller can learn approximately 70 to
90 commands, although this will be less if commands
that use a lot of memory are learned.
• Remote controller buttons such as Play, Stop, Pause,
and so on are preprogrammed with commands for
controlling Integra/Onkyo CD players, cassette decks,
and DVD players. However, they can learn new com-
mands, and you can restore the preprogrammed com-
mands at any time by resetting the remote controller
(see page 133).
•To overwrite a previously learned command, repeat
this procedure.
• Only commands from infrared remote controllers can
be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
Learning Commands
1
While holding down the Remote
Mode button for the mode in
which you want to use the com-
mand, press the [On] button.
The Remote indicator lights up.
2
Press the button you want to
learn the new command.
+
-
On Standby
TV
Input
TV CH
TV VOL
--
/
---
10 11 12
D.TUN
+10
0
Clear
123
456
789
Input Selector
VCR
/
DVR CBL
/
SAT
DVD
Tape
Tuner
CD
Phono Net/USB
Game
/
TV
Macro
123
VCRDVD
CDR/MD/Dock
CD
Zone
2
Remote Mode
Dimmer
Tape/AMP
Sleep
Receiver
TV
Net/USB
Cable
VOL
CH
Disc
Album
+
-
Enter
T
o
p
M
e
n
u
M
e
n
u
Display Muting
E
x
i
t
G
u
i
d
e
Prev
CH
R
e
t
u
r
n
S
e
t
u
p
SAT
Zone
3
AUX 1 AUX 2
1, 4
1
Remote
indicator
VCRDVD
CDR/MD/Dock
CD
Remote Mode
Tape/AMP
Receiver
TV
Net/USB
Cable
SAT
On
3
Point the remote controllers at
each other, about 2 to 6 inches
(5–15 cm) apart, and then press
and hold the button whose com-
mand you want to learn until the
Remote indicator flashes.
If the command is learned successfully,
the Remote indicator flashes twice.
4
To learn more commands, repeat
steps 2 and 3.
Press any Remote Mode button when
you’ve finished.
POWER
SLEEP
DIMM
ER
SU
R
MODE
VIDEO-1
VIDEO-2
TAPE
DVD
C D
C D
DVD
TUNER
TUNER
PHONO
INPUT SELE
CTOR
DISC
TAPE
VOLUME
EVEL
CH SEL
PRESET
MUTING
TEST
TONE
MULTI-CH
INPUT
GROUP
R
1
0
--
/-
-
-
1
1
1
2
R
emo
te M
ode
Z
o
n
e
2
DVD
VCR
CD
Z
o
n
e
3
Receiver
Cable
Net/USB
Tape/AM
P
SAT
CDR/MD/Dock
+
-
T
V
C
H
T
V
V
O
L
Sleep
Input Selector
3
2
Macro
1
+
10
0
Clear
D.TUN
1
2
3
4
5
6
7
8
9
In
p
u
t
I
O
n
S
t
a
n
d
b
y
T
V
T
a
p
e
D
V
D
D
C
R
/
D
V
R
C
B
L
/
S
A
T
AUX1
A
U
X
2
T
u
n
e
r
C
D
Phono
Net/USB
G
a
n
e
/T
V
About 2 to 6
inches (5–15 cm)
RC-688M
DTR-8.8En.book Page 135 Friday, February 15, 2008 1:17 PM
To Next Page
Loading...
Need help?
General
