What to do if JCM Technologies KEEROLL Control Panel shows a radio communication error?
If your JCM Technologies Control Panel displays a radio communication error, verify the radio signal. Actions to take include checking the batteries, reprogramming the system, or relocating the equipment.
General| Brand | JCM Technologies |
|---|---|
| Model | KEEROLL |
| Category | Control Panel |
| Language | English |
Guidance on safe installation procedures for the equipment, including power disconnection and height requirements.
Guidelines for safe operation of the door and controls, emphasizing child safety and monitoring.
Defines the intended application for garage door automation and manufacturer's right to change specifications.
Overview of the KEEroll solution for residential roller shutters, highlighting its features and user-friendliness.
Explanation of the LED indicators on the control panel and their meanings for system status.
Details the functions of the KEEroll control panel buttons for opening, closing, and other operations.
Describes functions like block transmitter, courtesy light, and alarm activation using the control panel.
Details the RadioSens3 impact detection system, its communication, and installation components.
Instructions on setting options and sensibility selectors before programming the RadioSens3 system.
Table showing estimated battery life for the RadioSens3 system based on daily maneuvers.
Introduction to the RadioBand3 wireless safety edge system for various door applications.
Provides dimensions and IP rating for the RadioBand3 system transmitter.
Describes the KEEpad 3-channel transmitter, its functions, and associated indicators.
Introduces the KEEpush 3-channel motion transmitter and its functions for door control.
Explains KEEalarm's role in monitoring doors and preventing intrusions with an acoustic alarm.
Introduces SESAME, a device for controlling residential doors via mobile phone.
Lists features like remote control, status checking, and low battery warnings for SESAME.
Provides dimensions for the KEEroll control panel and instructions for wall mounting.
Details on removing the front cover and installing the bottom part of the control panel on the wall.
Wiring diagram for connecting a 230VAC monophase motor to the KEEroll control panel.
Wiring for output terminals, including options for 230Vac, 24V/12V, or alarm signals.
Wiring for Opto safety edge and 8k2 safety edge inputs, including AUTOEDGE detection.
Connection diagrams for photocell and pushbutton inputs on the KEEroll control panel.
Instructions for connecting the power supply to the KEEroll control panel.
Procedure for adjusting the limit switch, with the door in the halfway position.
Table detailing dipswitch functions for Deadman, Autoclose, Pre-flash, Alarm, and other settings.
Defines the activation time for the courtesy light using control panel buttons and dipswitch settings.
Step-by-step guide to programming transmitters to control the door functions.
Detailed steps for programming door maneuvers, including safety element programming first.
Instructions on how to adjust the inhibition zone for RadioSens3 during closing movement.
Checks to ensure the control panel and system accessories are working correctly.
Procedure to check radio communication quality using the control panel LEDs.
Setting the number of maneuvers for the maintenance warning indicator.
Resets the manoeuvre counter to zero when the maximum number of movements is exceeded.
Procedure to erase all programmed transmitters from the system.
Guide on how to replace the fuse in the frontal panel if the device does not light up.
Table of indicators, their ON status, and corresponding troubleshooting solutions.
Key technical specifications of the KEEroll system, including power, size, and temperature.
Step-by-step guide for installing the RadioSens3 transmitter on the door's last slat.
Information on automatic detection of limit switches by the control panel before RadioSens3 installation.
Adjusting the RadioSens3 sensibility selector to fine-tune impact detection for different door speeds.
Procedure for entering installer mode and programming the RadioSens3 transmitter.
Instructions for replacing batteries in the RadioSens3 transmitter and expected battery duration.
Table correlating D1 (red) and D2 (green) LED flashes with specific issues and solutions.
Technical specifications for the RadioSens3 system, including frequency, memory, and range.
Visual guide for installing the RadioBand transmitter, including connections and programming.
Table detailing IN1 and IN2 connection settings for various safety edges and NC contacts.
Wiring diagram for connecting an 8k2 resistive safety edge to the RadioBand transmitter.
Wiring diagram for mechanical or contact safety devices connected to the RadioBand transmitter.
Wiring for standard optical safety edges, used with ATEST function.
Wiring for OSE-S7502B 'ALWAYS ON' optical safety edge and wicket door contact.
Instructions for entering installer mode and programming the RadioBand3 transmitter.
Indication table for LED and beep statuses during PROG button press or Check function.
Guide for replacing batteries in the RadioBand3 transmitter, noting low battery and no battery states.
Summary of technical data for RadioBand system, including frequency, consumption, range, and temperature.
Visual guide for installing KEEpad/KEEpush, including battery insertion and wall mounting.
Warning against installing near radiofrequency transmitting equipment to preserve battery life.
Instructions for programming KEEpad transmitters, including entering passwords for channels.
Guide for programming KEEpush transmitters by waking up the device and pressing buttons.
Verifying KEEpad operation by entering the password to open and stop/close the door.
Checking KEEpush functionality by waking up the device and pressing its buttons.
Steps for replacing batteries in KEEpad, including indicator for low battery status.
Procedure for changing the KEEpad password, including entering current and new passwords.
Steps for resetting the KEEpad, entering configuration mode and master code.
Table of common KEEpad issues, such as failure to wake up or program, and their solutions.
Technical specifications for KEEpad, including channels, power supply, and autonomy.
Instructions for programming the KEEalarm device using the KEEroll dipswitch and programming button.
Guide for installing KEEalarm, including placement, dimensions, and wiring of magnetic parts.
Checking KEEalarm LED status and procedures for deactivating and rearming the alarm.
Instructions for connecting the SESAME device to the KEEroll control panel via RJ-45.
Steps for configuring SESAME with a WiFi network, including searching and connecting to the SSID.
Guide to adding the SESAME device to the JCM Honoa mobile application using QR code or key.
Completing device details like name, place, and city within the Honoa app for setup.
Information on entering licenses for SESAME to enable its functionality, with details on available licenses.
Scanning or manually inputting the license code for SESAME and saving it in the app.
Verifying SESAME operation by checking door status (open/closed) and using control buttons.
Procedure for resetting SESAME, typically when changing Wi-Fi network or password.
Explanation of LED status indicators for SESAME during various operational states.
Detailed table of SESAME LED states (Status, Network, Internet) and corresponding actions.
Declaration by JCM Technologies stating KEEROLL compliance with RED, Machine, and RoHS Directives.
To Next Page