JUKI SC-910N Engineer's Manual

– 44 –
1 Soft start The number of stitches to be sewn at a low speed when the U 0 to 9 52
function soft-start function is used at the start of sewing. (Stitches)
2 Material end Material end sensor function (used in case of without panel). U 0/1 52
sensor 0 : Material end detection function is not operative
function 1 : After detecting material end, the specified number of
stitches (No. 4) will be sewn, and the sewing machine
will stop.
3 Thread trimming Thread trimming function by material end sensor (used in case of U 0/1 52
function by without panel).
material end 0 : Automatic thread trimming function after detection of
material end is not operative.
1 : After detecting the material end, sewing will be carried
out for the specified number of stitches (No. 4) and
the sewing machine will then stop.
4 Number of Number of stitches for material end sensor (used in case of U 0 to 19 52
stitches for without panel). Number of stitches from detection of material (Stitches)
material end end to stop of the sewing machine.
sensor
5 Flicker reducing Flicker reducing function (If the hand lamp flickers). U 0 to 8 52
function 0 : Flicker reducing function is not operative.
1 : Less effective . 8 : Highly effective
6 Bobbin thread Bobbin thread counting function U 0/1 52
counting 0 : Bobbin thread counting function is not operative. 53
function 1 : Bobbin thread counting function is operative.
7 Unit of bobbin Unit of bobbin thread counting down U 0 to 2
thread counting 0 : Count/10 stitches
down 1 : Count/15 stitches
2 : Count/20 stitches
8 Number of Sewing speed of reverse feed stitching U 150 to 3000
rotation of (rpm)
reverse feed
stitching
9 Thread Thread trimming prohibiting function (used in case of U 0/1 52
trimming without panel).
prohibiting 0 : Thread trimming prohibiting function is not operative.
function 1 : Thread trimming is prohibited.
(Output of solenoid is prohibited. : Thread trimmer and
wiper)
10 Setting of Position of needle bar is specified when the sewing U 0/1 52
needle bar machine stops.
stop position 0 : Predetermined lowest position
when the sewing 1 : Predetermined highest position
machine stops.
11 Click sound of Click sound of key switch mounted on PSC is specified. U 0/1 53
key switch 0 : Click is not operative.
mounted on 1 : Click is operative.
PSC
12 Optinal switch Switching of function of optional switch. U 0 to 8 53
function 0 : No function
selection 1 : Needle up/down compensating stitching
2 : Back compensating stitching
3 :Function of canceling once reverse feed stitching at the
end of sewing
4 : Thread trimming function
5 : Presser foot lifting function
6 : One stitch compensating stitching
7 : Function of simultaneously canceling reverse feed
stitching at the
start and end of sewing
8 : Neutral presser lifting changeover function
13 Function of Function of prohibiting start of the sewing machine by bobbin U 0 to 2 62
prohibiting thread counting
start of the 0 : When counting is out (-1 or less) Function of
sewing prohibiting start of the sewing machine is not operative.
machine by 1 : When counting is out (-1 or less) Function of prohibiting
bobbin thread start of the sewing machine is operative.
counter 2 : When counting is out (-1 or less) Function of forcibly
prohibiting start of the sewing machine is operative.
(9) Function setting list (Start level ; U : User’s mode, S : Service mode)
No. Item Description Start level Setting range
1
0
2
0
3
0
4
5
5
0
6
1
7
0
8
0
0
9
1
9
0
0
1
0
1
1
1
2
1
0
3
1
0
Indication of
function setting
Ref.
page

JUKI SC-910N Specifications

General

Brand	JUKI
Model	SC-910N
Category	Sewing Machine
Language	English