9
ANTRIEBSTECHNIK
1
19
05.01.99
KEB COMBIVERT F4-C
Name:Basis
1
Introduction
General
© KEB Antriebstechnik, 1997
All Rights reserved
Chapter
Section
Page
Date
6.3 Digital In- and Outputs......................................................................6.3.3
6.3.1 Short Description Digital Inputs...........................................6.3.3
6.3.2 Input Signals PNP / NPN (di.1) ........................................... 6.3.3
6.3.3 Terminal Status (ru.14) ........................................................6.3.4
6.3.4 Set Digital Inputs with Software (di.15, di.16)......................6.3.4
6.3.5 Digital Filter (di.0) ................................................................6.3.5
6.3.6 Inverting of the Inputs (di.2).................................................6.3.5
6.3.7 Edge Triggering (di.14) ........................................................6.3.5
6.3.8 Strobe-dependent Inputs(di.17...di.19)................................ 6.3.6
6.3.9 Mode of Rotation setting (di.20 Bit0) ...................................6.3.7
6.3.10 Functional Assignment (di.3...di.10) ....................................6.3.8
6.3.11 Input status (ru.16) ..............................................................6.3.8
6.3.12 Reset-Mode ST (di.21) ........................................................6.3.8
6.3.13 Short Description - Digital Outputs ......................................6.3.9
6.3.14 Output Signals...................................................................6.3.10
6.3.15 Output Conditions (do.1...do.4) .........................................6.3.10
6.3.16 Inverting Output Conditions do.17...do.24 .........................6.3.12
6.3.17 Selection Output Conditions (do.9...do.16)........................6.3.12
6.3.18 Output Condition Interconnection (do.25) .........................6.3.12
6.3.19 Inverting of the Outputs (do.0)..........................................6.3.13
6.3.20 Output Terminal Status (ru.15) .........................................6.3.13
6.3.21 Used Parameters ..............................................................6.3.13
6.4 Set Value and Ramp Adjustment ......................................................6.4.3
6.4.1 Short Description ................................................................6.4.3
6.4.2 AUX-Function ......................................................................6.4.4
6.4.3 Set Value Limits...................................................................6.4.9
6.4.4 Set Value Calculation ........................................................6.4.10
6.4.5 Fixed Frequencies (oP.22...24) ..........................................6.4.11
6.4.6 Ramp Generator................................................................6.4.12
6.4.7 Used Parameters ..............................................................6.4.18
6.5 Voltage-/Frequency Characteristic ...................................................6.5.3
6.5.1 Maximal Frequency Mode (ud.11).......................................6.5.3
6.5.2 Rated Point (uF.0) and Boost (uF.1) ....................................6.5.3
6.5.3 Additional Rated Point (uF.2/uF.3) .......................................6.5.3
6.5.4 Delta Boost (uF.4/uF.5) ........................................................ 6.5.4
6.5.5 UZK-Compensation (uF.8)...................................................6.5.4
6.5.6 Modulation...........................................................................6.5.5
6.5.7 Operating Frequency (uF.11)...............................................6.5.6
6.6 Motor Presetting.................................................................................6.6.3
6.6.1 Motor Rating Plate ..............................................................6.6.3
6.6.2 Motor Data from Rating Plate (dr.1...dr.4, dr.12) .................6.6.3
6.6.3 Motor Data from Data Sheets (dr.22) ..................................6.6.3
6.6.4 Motor Stator Resistance (dr.5) ............................................6.6.4
To Next Page
Loading...
Need help?
General