KEB COMBIVERT F5 BASIC - Page 9

9
1
19
28.02.02
KEB COMBIVERT F5-G / B
Name:Basis
1
Introduction
General
© KEB Antriebstechnik, 2002
All Rights reserved
Chapter Section PageDate
6.2.9 Selection Set Point-/Auxiliary Input (An.30)......................... 6.2.9
6.2.10 Brief Description Analog Outputs ...................................... 6.2.10
6.2.11 Output signals ................................................................... 6.2.11
6.2.12 Analog Output / Functions (An.31/An.36/An.41) ............... 6.2.11
6.2.13 Analog Output / Display..................................................... 6.2.12
6.2.14 Gain of Output Characteristic (An.33...35 /An.38...40 /
An.43...45) ......................................................................... 6.2.12
6.2.15 Period ANOUT3 (An.46).................................................... 6.2.13
6.2.16 ANOUT 1...4 Digital Settings (An.32/37/42/48) ................. 6.2.13
6.2.17 Used Parameters.............................................................. 6.2.14
6.3 Digital In- and Outputs ....................................................................... 6.3.3
6.3.1 Summary Description Digital Inputs .................................... 6.3.3
6.3.2 Input Signals PNP / NPN (di.0) ........................................... 6.3.3
6.3.3 Setting of Digital Inputs by Software (di.1, di.2) ................... 6.3.4
6.3.4 Terminal Status (ru.21) ........................................................ 6.3.5
6.3.5 Digital Filter (di.3) ................................................................ 6.3.5
6.3.6 Inversion of Inputs (di.4) ...................................................... 6.3.5
6.3.7 Edge-triggering (di.5)........................................................... 6.3.5
6.3.8 Strobe-dependent Inputs (di.6, di.7, di.8)............................. 6.3.6
6.3.9 Input Status (ru.22) .............................................................. 6.3.8
6.3.10 Reset/Input Selection and Edge Evaluation
(di.9 / di.10).......................................................................... 6.3.8
6.3.11 Assignment of the Inputs ..................................................... 6.3.8
6.3.12 Summary Description - Digital Outputs.............................. 6.3.11
6.3.13 Output Signals................................................................... 6.3.12
6.3.14 Output filter (do.43, do.44).................................................. 6.3.12
6.3.15 Switching Conditions (do.0...do.7) ..................................... 6.3.13
6.3.16 Inverting of Switching Conditions for Flags (do.8...do.15).. 6.3.16
6.3.17 Selection of Switching Conditions for Flags (do.16...do.23)6.3.16
6.3.18 Linking the Switching Conditions for Flags (do.24) ........... 6.3.16
6.3.19 Inverting of Flags (do.25...do.32) ....................................... 6.3.17
6.3.20 Selection of Flags (do.33...do.40) ...................................... 6.3.17
6.3.21 Linking the Flags (do.41) ................................................... 6.3.17
6.3.22 Inversion of Outputs (do.42) ............................................... 6.3.18
6.3.23 Output Terminal Status (ru.25) ........................................... 6.3.18
6.3.24 Programming Example...................................................... 6.3.19
6.3.25 Used Parameters............................................................... 6.3.20
6.4 Setpoint-, Rotation- and Ramp Adjustment ..................................... 6.4.3
6.4.1 Summary Description .......................................................... 6.4.3
6.4.2 Setpoint Selection oP.0 ....................................................... 6.4.4
6.4.3 Rotation Selection oP.1 ....................................................... 6.4.6
6.4.4 Fixed Frequencies (oP.18...23) ............................................ 6.4.9
6.4.5 Setpoint Limits................................................................... 6.4.11
6.4.6 Setpoint Computation........................................................ 6.4.12
6.4.7 Ramp Generator................................................................ 6.4.13