Page 1.1 - 12 COMBIVERT F5-A, -E, -H © KEB, 2008-02
Table of contents
7.14.8 Locking of parameter sets ...........................................................................7.14 - 12
7.14.9 Set activation/deactivation delay (Fr.05, Fr.06) ...........................................7.14 - 12
7.15 Special functions ........................................................................................7.15 - 3
7.15.1 DC-braking ....................................................................................................7.15 - 3
7.15.1.1 V/F characteristic control ....................................................................................7.15 - 5
7.15.1.2 Speed-controlled operation without feedback (ASCL) .......................................7.15 - 5
7.15.2 Energy saving function ..................................................................................7.15 - 6
7.15.3 Motorpoti function .........................................................................................7.15 - 7
7.15.4 Timer / counter programming ........................................................................7.15 - 9
7.15.5 Brake control ...............................................................................................7.15 - 13
7.15.5.1 Mode brake control ...........................................................................................7.15 - 13
7.15.5.2 Monitoring of the brake control .........................................................................7.15 - 14
7.15.5.3 Sequence of the brake control .........................................................................7.15 - 14
7.15.5.4 Brake control / vector controlled .......................................................................7.15 - 16
7.15.5.5 V/F characteristic controlled operation ............................................................. 7.15 - 17
7.15.6 Sweep generator .........................................................................................7.15 - 18
7.15.7 Diameter correction ....................................................................................7.15 - 20
7.15.8 Analog setting of parameter values ............................................................7.15 - 22
7.15.9 Register function ......................................................................................... 7.15 - 23
7.15.10 Technology control ...................................................................................... 7.15 - 26
7.15.10.1 The PID controller.............................................................................................7.15 - 26
7.15.10.2 PID setpoint ......................................................................................................7.15 - 28
7.15.10.3 PIDactual value ................................................................................................7.15 - 30
7.15.10.4 Application examples........................................................................................7.15 - 31
7.16 CP-Parameterdenition ............................................................................. 7.16 - 3
7.16.1 Overview ....................................................................................................... 7.16 - 3
7.16.2 Assignment of CP-Parameters .....................................................................7.16 - 4
7.16.3 Example ........................................................................................................ 7.16 - 5
7.16.4 Display norm ................................................................................................. 7.16 - 6
7.16.5 Variable norm ................................................................................................7.16 - 9
8. Error Assistance ....................................................................................8.1 - 3
8.1 Troubleshooting ............................................................................................8.1 - 3
8.1.1 General ...........................................................................................................8.1 - 3
8.1.2 Error Messages and their Cause ....................................................................8.1 - 3
9. Project Design .......................................................................................9.1 - 3
9.1 General designs ............................................................................................ 9.1 - 3
9.1.1 Control cabinet design calculation ..................................................................9.1 - 3
9.1.2 Design of braking resistors .............................................................................9.1 - 4
9.1.3 Cables and fuses ............................................................................................9.1 - 7
10. Networks ..............................................................................................10.1 - 3
10.1 Network components .................................................................................10.1 - 3
10.1.1 Available hardware .......................................................................................10.1 - 3
10.1.2 RS232 cable PC / operator 00.58.025-001D ................................................10.1 - 3
10.1.3 HSP5 cable / control board 00.F5.0C0-0010 ................................................ 10.1 - 4
To Next Page
Loading...
