Keithley 6517 - Figure 2-7 Connections for Voltage Source Calibration; Table; Voltage Source Calibration Summary

Calibration
2-13
3. Temporarily short the ends of the DMM test leads, then
enable the DMM REL mode. Leave REL enabled for the
remainder of the tests.
4. Connect the DMM to the V SOURCE OUT jacks, as
shown in Figure 2-7.
5. Press ENTER. The Model 6517A will prompt you for
0V output:
V-SOURCE 0: 100V RNG
Press ENTER to output 0V
6. Press ENTER, and note that the instrument prompts for
the actual DMM reading:
DMM RDG: +0.00000 V
Use ▲, ▼, , ,ENTER,EXIT or INFO
7. Adjust the Model 6517A display so that it agrees exactly
with the voltage reading on the DMM, then press the
ENTER key.
8. Repeat steps 6 and 7 for each voltage source output val-
ue summarized in Table 2-7. For each step, be sure to ad-
just the Model 6517A display to agree exactly with the
DMM reading.
Figure 2-7
Connections for voltage source calibration
WARNING: NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.
WARNING: NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.
INPUT
250V PEAK
!
LINE RATING
50-60HZ
50VA MAX
AC ONLY
LINE FUSE
SLOWBLOW
1/2A 90-125V
1/4A 180-250V
IEEE-488
(CHANGE IEEE ADDRESS
WITH FRONT PANEL MENU)
DIGITAL
I/O
TRIG LINK
115V
LO
HI
RS232
!
MADE
IN
U.S.A.
PREAMP OUT
250 PEAK
COMMON 2V ANALOG
OUTPUT
TEMP
TYPE K
HUMIDITY
OPTION SLOT
V SOURCE
EXT TRIG
IN
MTR COMP
OUT
INTERLOCK
SELECTED
LINE VOLTAGE
90-110V
105-125V
180-220V
210-250V
1010V
PEAK
750V
PEAK
Model 2001 DMM
Output LO
Model 6517 Electrometer
NEXT
PREV
POWER
DISPLAY
2001 MULTIMETER
DCV ACV DCI ACI Ω2 Ω4
FREQ TEMP
REL TRIG
INFO LOCAL EXIT ENTER
RANGE
RANGE
!
FR
500V
PEAK
FRONT/REAR
2A 250V
AMPS
CAL
STORE RECALL
CHAN SCAN
FILTER MATH
CONFIG MENU
HI
INPUT
LO
SENSE
Ω 4 WIRE
INPUTS
350V
PEAK
1100V
PEAK
AUTO
Output HI
Input HI
Input LO
Table 2-7
Voltage source calibration summary
Nominal
output Display prompt Comments
0V
+40V
+100V
-100V
0V
+400V
+1000V
-1000V
DMM RDG: +0.00000 V
DMM RDG: +40.0000 V
DMM RDG: +100.0000 V
DMM RDG: -100.0000 V
DMM RDG: 0.00000 V
DMM RDG: +400.000 V
DMM RDG: +1000.000 V
DMM RDG: -1000.000 V
100V range cali-
bration
1000V range cali-
bration
NOTE: For each calibration step, adjust the displayed value to agree
with the DMM reading.