Korg PS60 User Manual

Performance edit Quick parameter list
33
MFX1 (Mod.)
About the master effects
The master effects do not output any direct sound
(Dry). Use the return levels “Return1” and “Return2”
to return the effect sound (Wet) to the L/R bus and mix
it into the signal of the L/R bus.
The master effects are stereo-in/stereo-out, but the
output may be monaural depending on the type of
effect that’s selected.
Tip: You can use the front panel MODULATION but-
ton and knobs to directly control the Effect Type and
MFX Parameters.
Tip: You can use the Copy MFX/EQ command to copy
the master effect and EQ settings from another perfor-
mance or program.
Effect Type [No Effect...St.Phaser]
This selects the effect type for master effect 1.
Choose from No Effect, St.Chorus, St.Flanger,
Vntg.Cho/Flg, and St.Phaser. If you choose No Effect,
the output from the master effect will be muted.
MFX1 Parameters
Here you can set the parameters of the effect
selected by “Effect Type.” These are displayed if
you press the  button when selecting Effect Type.
St.Chorus (Stereo Chorus)
St.Flanger (Stereo Flanger)
Vntg.Cho/Flg (Vintage Chorus/Flanger)
St.Phaser (Stereo Phaser)
( “Effect types,” p. 20)
Rate (Hz) [0.01...10.0]
This adjusts the speed of LFO modulation.
Depth [0...100]
This adjusts the depth of LFO modulation.
Feedback [0...100]
This adjusts the amount of feedback.
On/Off [Off, On]
This turns master effect 1 on/off. When off, the output
is muted.
Return 1 [000...127]
This specifies the return level from master effect 1 to
the L/R bus.
Chain [Off, On]
On: Master effects 1 and 2 will be series-connected in
the order of master effect 1 → master effect 2.
Chain Level [000...127]
This specifies the level from master effect 1 to master
effect 2 when “Chain On/Off” is On.
Tip: You can use the front panel MODULATION but-
ton and knobs to directly control the Effect Type and
MFX Parameters.
MFX2 (Rev/Dly)
( “About the master effects,” p. 33)
Effect Type [No Effect...Delay]
This selects the effect type for master effect 2.
You can choose from No Effect, Hall, Plate, Room, or
Delay. If you choose No Effect, the output from the
master effect will be muted.
MFX2 Parameters
Here you can set the parameters of the effect
selected by “Effect Type.” These are displayed if
you press the  button when selecting Effect Type.
Hall
Plate
Room
( “Effect types,” p. 20)
Time (sec) [Hall, Plate: 0.1...10.0]
[Room: 0.1...3.0]
This specifies the reverb time.
Level [0...100]
This adjusts the output level of the reverb.
Feedback [0...100]
This adjusts the amount of high-frequency
attenuation.
Delay
( “Effect types,” p. 20)
Time (msec) [0...549]
This adjusts the delay time.
Level [0...100]
This adjusts the output level of the delay sound.
Feedback [0...100]
This adjusts the feedback amount of the delay
sound.
On/Off [Off, On]
This turns master effect 2 on/off.
Return 2 [000...127]
This specifies the return level from master effect 2 to
the L/R bus.
Note: The actual level is determined by multiplying
this value with the Level parameter value of Hall,
Plate, Room, or Delay.
Tip: You can use the front panel REVERB/DELAY but-
ton and knobs to directly control the Effect Type and
the MFX Parameters.
MFX2(Rev/Dly)
MFX1(Mod)
Return 1
Return 2
AUDIO OUTPUT
L/Mono, R
stereo
Modulation
Reverb/Delay
stereo
stereo
Chain On/O
Chain
Level
Send1
Send2
L/R
stereo
stereo
stereo
EQ
Master Level
EQ

Korg PS60 Specifications

General

Type	Performance Synthesizer
Synthesis Type	Sample-based synthesis
Velocity Sensitivity	Yes
Aftertouch	No
Arpeggiator	Yes
Sequencer	No
MIDI	In, Out, Thru
Power Supply	DC 9V
Keyboard	61 keys
Sound Engine	EDS-i
Effects	2 Master effects
Controllers	Pitch bend, modulation wheel
Outputs	2 x 1/4" (L/R)
USB	Type B x 1
Sound Generator	EDS-i
Preset Programs	440 programs
Polyphony	120 voices (120 Oscillators)
Inputs	1 x 1/4" (damper)