Kubota KX080-3 - Excavator Operation; Running-in of the New Excavator; Do Not Work with Full Engine Rpms or Full Loads During the First 50 Working Hours; Oil Change in the Run-in Stage

115 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Table of Contents5
Dealer Service23
Safe Operation23
Technical Data24
Description of Machine Parts25
Instrument Panel and Control Elements26
Checks before Start28
- Daily Checks28
- Air Conditioner32
- Handling the Safety Devices34
  - Control Lever Lock34
Operation of the Engine35
- Starting the Engine35
- Starting the Engine under Cold Conditions42
- Stopping the Engine42
  - Engine Stop Button42
- Starting with an Auxiliary Battery43
  - Observe Following Guidelines When Starting with an Auxiliary Battery43
Excavator Operation44
- Running-In of the New Excavator44
- Starting44
  - Adjusting the Operator's Seat45
  - Lock Lever45
- Driving46
  - Drive Levers(Right,Left)47
  - Travel Speed Switch48
- Turns49
  - Pivot Turn49
  - Spin Turn50
- Up and Downhill Driving50
- Parking on a Slope51
- Operation of the Dozer51
- Two Pattern Selection System(Tpss)52
  - Pattern Change52
- Operation of the Boom53
- Operation of the Arm53
- Operation of the Bucket54
- Unit Swing and Boom Swing Operation54
  - Unit Swing Operation54
  - Boom Swing Operation55
- Service Port Operation56
- 1-Way or 2-Way CIRCUIT SELECTION VALVE OPERATION62
- Emergency Shut-Off Valve63
- Boom Lowering Valve63
- Auto Idle (Ai) Operation64
- Important Information on Excavator Operation64
- How to Release Pressure Trapped in the Hydraulic System65
Transporting the Excavator on a Vehicle66
Lifting of the Excavator68
Maintenance70
- Maintenance Intervals70
- Opening and Closing of Parts73
- Daily Checks76
Regular Checks and Maintenance Work81
- Every 50 Service Hours81
- Every 100 Service Hours83
  - Greasing Boom Swing Fulcrum83
- Every 200 Service Hours84
- Air Conditioner87
  - Cleaning Air Filter87
  - Checking Air-Conditioner Condenser88
- Every 250 Service Hours89
- Every 500 Service Hours91
- Every 1000 Service Hours93
- Every 1000 Service Hours or Once Ayear95
  - Replacing Air Filter Element95
- Every 1500 Service Hours96
  - Checking Fuel Injection Nozzle(Injection Pressure)96
- Every 2000 Service Hours96
  - Changing Front Idler and Track Roller Oil96
  - Checking the Alternator and Starter Motor96
- Every 3000 Service Hours96
  - Checking Injection Pump96
- Annual Servicing96
- Servicing as Required99
  - Checking Amount of Refrigerant (Gas)99
Other Adjustments and Replacements100
- Purging of the Fuel System100
- Adjustment of Tracks100
  - Special Information When Using Rubber Tracks101
- Changing the Bucket102
- Fuses102
Troubleshooting104
- Kubota I.C.s. Navigation List of Messages106
Operation under Cold Weather Conditions108
- Preparation for Operation in Cold Weather108
- Procedure after Done Work108
Long Storage109
Recommended Oils111
Appendices113
- Main Dimensions113
Lifting Capacity114

Other manuals for Kubota KX080-3

Workshop Manual758 pages

Related product manuals

Preview: Kubota KX080-4

Preview: Kubota KX057-4

Preview: Kubota KX015-4

Preview: Kubota KX033-4

Preview: Kubota KX057-4 U55-4

Kubota KX057-4 U55-4

Preview: Kubota KX71-3

Preview: Kubota KX61-3

Preview: Kubota KX91-3a

Kubota KX121-3a

Preview: Kubota KX 016-4

Kubota KX 016-4

Preview: Kubota KX91-3a2

Kubota KX91-3a2