What to do if Kubota Excavators engine suddenly stops?
If your Kubota Excavators engine suddenly stops, it might be due to a low fuel level, which requires checking the fuel and adding more if necessary. It may also be necessary to purge the fuel system.
Why is the water temperature in red zone (Overheating) in my Kubota KX080-4?
If your Kubota Excavators is overheating with the water temperature in the red zone, several issues could be the cause. It could be due to a defective seal of the water pump, requiring a replacement. A worn or torn V-belt may need adjustment or replacement. A defective thermostat also warrants replacement. Low coolant level should be addressed by filling to the prescribed level. Clogged radiator grill or fins need cleaning. Coolant contaminated with rust requires replacement and the addition of anti-rust. A defective radiator cap should be replaced. Corroded coolant pipes should be cleaned. Lastly, continuous operation under full load may necessitate reducing the load.
How to troubleshoot starting difficulties with Kubota Excavators?
If your Kubota Excavators won't start, there are several potential causes. Ensure the lock levers are in the "LOCK" position. If the fuel is too viscous, check the fuel tank and filter for impurities and water, replacing the filter if necessary. Air or water in the fuel system requires removing water from the fuel tank and checking fuel pipe joint bolts and nuts for looseness. You may need to purge the fuel system. If the oil viscosity is too high, especially in winter, pour hot water over the radiator. Lastly, a nearly dead battery or insufficient compression requires recharging the battery.
What to do if Kubota KX080-4 water temperature is in red zone (Overheating)?
If your Kubota Excavators experiences overheating with the water temperature in the red zone, it could be due to several reasons. A damaged cylinder head gasket causing coolant loss requires replacement. Low engine oil level needs to be corrected by filling to the prescribed level. Maladjustment of fuel injection requires readjusting the ignition timing. Also, the use of poor fuel necessitates switching to prescribed fuel.
Why does my Kubota KX080-4 have insufficient engine power?
If your Kubota Excavators has insufficient engine power, it could be due to a low fuel level, which requires checking and adding fuel if necessary. Another cause could be a clogged air cleaner, which requires cleaning the air filter element.
What causes low power in boom, arm, bucket, drive, swing and dozer of Kubota KX080-4?
If the boom, arm, bucket, drive, swing, and dozer power is too low on your Kubota Excavators, it could be due to a low hydraulic oil level, which requires adding oil. Alternatively, there may be leakages of hoses and/or joints, which require replacing the hose or joint.
Why does Kubota Excavators have abnormal exhaust gas color?
If your Kubota Excavators is emitting abnormal exhaust gas, it could be due to poor fuel quality, which requires using high-quality fuel. Alternatively, there might be too much engine oil, which requires draining the engine oil to the prescribed level.
What to do if swing motor and front attachment does not work in Kubota KX080-4?
If the swing motor and front attachment on your Kubota Excavators do not work, ensure the lock lever is in the "UNLOCK" position by bringing it into the correct position.
Why Kubota KX080-4 has deviation of drive direction?
If your Kubota Excavators experiences deviation of drive direction, it could be due to stones blocking the tracks, which requires removing them. Alternatively, the track may be too loose or too tight, requiring adjustment.
What does it mean if system indicator light flashes on Kubota KX080-4?
If the system indicator light flashes on your Kubota Excavators, it indicates that a fuse in the fuse box is defective and needs to be replaced.
Safety information and symbols used in the manual.
Pre-operation checks and safety guidelines.
Safe procedures for operating the excavator.
Procedures for shutting down and securing the excavator.
Guidelines for safely loading and transporting the machine.
Important procedures for keeping the machine in good condition.
Identification and function of control pedals and levers.
Essential checks to perform before each operation.
How to check and use various machine devices.
How to set the machine's clock.
Information on periodic maintenance checks.
Enabling and disabling the auto idle function.
How to inhibit or enable DPF regeneration.
Operation of the windshield wiper and washer.
How to turn on the interior cabin lamp.
Operation of the cabin heater.
Procedures for opening and closing the cabin door.
Location and use of the emergency hammer.
How air flows within the cabin.
Adjusting air flow direction from cabin vents.
Overview of the air conditioner control panel.
How to use the pilot control lock lever for safety.
Step-by-step guide to starting the engine.
How to jump-start the excavator with an auxiliary battery.
Procedures for safely stopping the engine.
Understanding and managing the DPF regeneration process.
Importance of breaking in new excavators.
How to adjust the operator's seat for comfort and safety.
Safe driving techniques for the excavator.
Safe driving on slopes.
How to operate the dozer blade.
How to change between control patterns.
Operating the upper structure swing.
Operating the boom swing.
Choosing operating modes for auxiliary ports.
Step-by-step guide for using auxiliary ports.
Adjusting hydraulic flow for attachments.
Maintenance tasks for every 50 service hours.
Procedure to drain water from the fuel tank.
How to drain water from the fuel water separator.
Checking and maintaining the excavator battery.
Maintenance tasks for every 100 service hours.
Lubricating the boom swing fulcrum.
Maintenance tasks for every 200 service hours.
How to adjust the tension of V-belts.
Inspecting radiator hoses and clamps for wear.
How to inspect and clean the air filter element.
Procedures for maintaining the air filter.
Maintenance tasks for every 250 service hours.
Maintenance tasks for every 500 service hours.
Procedure for changing engine oil.
Procedure for replacing the engine oil filter.
Maintenance tasks for every 1000 service hours.
How to replace the hydraulic pilot filter element.
Procedure for changing hydraulic oil and suction filter.
Maintenance tasks for 1000 hours or annually.
Maintenance tasks for every 1500 service hours.
Maintenance tasks for every 2000 service hours.
Maintenance tasks for every 3000 service hours.
How to clean the Diesel Particulate Filter (DPF).
Checking electrical wiring and fuses.
Inspecting AC pipes and hoses.
Replacing AC pipes and hoses every two years.
Procedure for changing the radiator coolant.
Checking the refrigerant level in the AC system.
Procedure to drain water from the fuel filter.
Removing air from the fuel system.
Adjusting track tension for optimal performance.
Safe procedure for changing the excavator bucket.
Information on auxiliary electric power circuits.
Details about slow blow fuses and their replacement.
Preparing the excavator for cold weather.
Post-operation procedures for cold weather.
Schedule for timely replacement of critical parts.
Key physical dimensions of the excavator.
Displays shown during normal operation.
Error messages and their meanings on the LCD display.
General| Engine Power | 66.4 HP |
|---|---|
| Bucket Capacity | 0.28 m3 / 0.37 yd3 |
| Max Digging Depth | 15 ft 1 in |
| Max Reach | 7320 mm / 24 ft |
| Max Dumping Height | 5, 280 mm |
| Max Digging Radius | 7, 660 mm |
| Width | 7 ft 2 in |
| Transport Height | 8 ft 4 in |
| Travel Speed | 5.0 km/h |
To Next Page
