Labconco Protector Echo 180 Series - Page 147

193 pages

To Next Page

To Previous Page

Appendix E: gGuard

Product Service 1-800-522-7658

142

Original instructions

6. Next it will show the directory where it will install gGuard on the PC. Just let it

install it where it wants, like below. Choose “everyone” and press next.

7. Then follow the prompts at this screen, press next.

Main Page

Default Chapter3
- Table of Contents3
Chapter 1: Introduction6
- Model Number Configurator7
- About this Manual8
- Typographical Conventions9
- Your Next Step10
Chapter 2 Prerequisites11
- Location Requirements12
- Support Requirements12
- Filtration Technology Airflow and Power Requirements12
- Electrical Requirements13
- Service Line Requirements13
- Space Requirements13
- Commissioning, Setup and Startup Requirements13
Chapter 3: Getting Started14
- Unpacking Your Fume Hood15
- Removing the Shipping Skid15
- Sash Weight Release16
- Installing the Hood on a Supporting Structure and Work Surface16
- Connecting the Electrical Supply Source to the Protector Hood18
- Connecting the Service Lines to the Protector Hood20
- Sealing the Protector Hood to the Work Surface21
- Setting up the Protector Echo Floor-Mounted Filtered Hood21
- Commissioning the Filtration Technology22
- Re-Configuration Process32
- Troubleshooting Guide for GFH48
- Certifying the Protector Filtered Fume Hood51
Chapter 4 : Performance Features and Safety52
Precautions52
- Performance Features52
- Safety Precautions56
Chapter 5: Using the Protector Filtered Hood64
- Access Cards64
- Starting the Filtered Hood65
- Operating the Vertical-Rising Sash65
- The Modular Neutrodine Filtration65
- Detecting a Breakthrough66
- Communication68
- User Options and Approved Chemicals69
- Working in Your Protector Filtered Fume Hood69
Chapter 6: Maintaining the Protector Filtered Hood71
- Routine Maintenance Schedule71
- Initial Certification72
- Re-Certification72
- User Alarm Code List72
- Tool List75
- Neutrodine SDS for Disposal76
- Partial Filter Replacement Procedure78
- Reconfiguration Process92
- Light And/Or Circuit Board Replacement93
- Fan And/Or Circuit Board Replacement95
- Fan Box Replacement97
- Electro (Acid) Sensor Replacement100
- Secure Mode108
- Gguard Checklist and Software Option109
- Bacnet Checklist Option109
Chapter 7: Accessorizing the Protector Filtered Hood110
- Filters110
- Work Surfaces111
- Base Stands, Accessory Shelves, Seismic Supports, and Hydraulic Lift Base Stands112
- Storage Cabinets113
- Installing Additional Service Fixtures113
- Installing an Electrical Duplex Outlet115
- Installing Optional Guardian™ Digital Airflow Monitor116
- Sash Stop Kit - Field Installation116
- Distillation Grids - Field Installation117
- Installing Remote Monitoring Software117
- Installing Bacnet Gateway Hardware118
- ADA Remote Control118
- Additional User, Maintenance, and Administrator Access Cards118
- Sash Reduction Wing Kits119
Chapter 8: Troubleshooting120
- Neutrodine Filtration Technology Replacement Parts124
Appendix A: Protector Filtered Hood127
Appendix B Protector Filtered Hood Dimensions127
Appendix C Protector Filtered Hood Specifications130
Appendix D Serial Number Tag Description132
APPENDIX E: Gguard138
Appendix Fbac Net153
Appendix G: Secure Mode156
Appendix H: Chemical Guide160
Appendix I References176
Appendix J: Setting up the Protector Echo Floor-Mounted Filtered Hood178
Appendix K: Small 54.2" Height Airo Dimensions190

Labconco Protector Echo 180 Series - Page 147

Table of Contents

Related product manuals