Labconco Protector Echo 180 Series - Appendix K: Small 54.2 Height Airo Dimensions

193 pages

To Next Page

To Previous Page

Product Service 1-800-522-7658

185

Original instructions

APPENDIX K

SMALL 54.2" HEIGHT

AIRO DIMENSIONS

The following pages provide dimensional data for the small 54.2" height Protector

Airo Filtered Fume Hoods.

Main Page

Default Chapter3
- Table of Contents3
Chapter 1: Introduction6
- Model Number Configurator7
- About this Manual8
- Typographical Conventions9
- Your Next Step10
Chapter 2 Prerequisites11
- Location Requirements12
- Support Requirements12
- Filtration Technology Airflow and Power Requirements12
- Electrical Requirements13
- Service Line Requirements13
- Space Requirements13
- Commissioning, Setup and Startup Requirements13
Chapter 3: Getting Started14
- Unpacking Your Fume Hood15
- Removing the Shipping Skid15
- Sash Weight Release16
- Installing the Hood on a Supporting Structure and Work Surface16
- Connecting the Electrical Supply Source to the Protector Hood18
- Connecting the Service Lines to the Protector Hood20
- Sealing the Protector Hood to the Work Surface21
- Setting up the Protector Echo Floor-Mounted Filtered Hood21
- Commissioning the Filtration Technology22
- Re-Configuration Process32
- Troubleshooting Guide for GFH48
- Certifying the Protector Filtered Fume Hood51
Chapter 4 : Performance Features and Safety52
Precautions52
- Performance Features52
- Safety Precautions56
Chapter 5: Using the Protector Filtered Hood64
- Access Cards64
- Starting the Filtered Hood65
- Operating the Vertical-Rising Sash65
- The Modular Neutrodine Filtration65
- Detecting a Breakthrough66
- Communication68
- User Options and Approved Chemicals69
- Working in Your Protector Filtered Fume Hood69
Chapter 6: Maintaining the Protector Filtered Hood71
- Routine Maintenance Schedule71
- Initial Certification72
- Re-Certification72
- User Alarm Code List72
- Tool List75
- Neutrodine SDS for Disposal76
- Partial Filter Replacement Procedure78
- Reconfiguration Process92
- Light And/Or Circuit Board Replacement93
- Fan And/Or Circuit Board Replacement95
- Fan Box Replacement97
- Electro (Acid) Sensor Replacement100
- Secure Mode108
- Gguard Checklist and Software Option109
- Bacnet Checklist Option109
Chapter 7: Accessorizing the Protector Filtered Hood110
- Filters110
- Work Surfaces111
- Base Stands, Accessory Shelves, Seismic Supports, and Hydraulic Lift Base Stands112
- Storage Cabinets113
- Installing Additional Service Fixtures113
- Installing an Electrical Duplex Outlet115
- Installing Optional Guardian™ Digital Airflow Monitor116
- Sash Stop Kit - Field Installation116
- Distillation Grids - Field Installation117
- Installing Remote Monitoring Software117
- Installing Bacnet Gateway Hardware118
- ADA Remote Control118
- Additional User, Maintenance, and Administrator Access Cards118
- Sash Reduction Wing Kits119
Chapter 8: Troubleshooting120
- Neutrodine Filtration Technology Replacement Parts124
Appendix A: Protector Filtered Hood127
Appendix B Protector Filtered Hood Dimensions127
Appendix C Protector Filtered Hood Specifications130
Appendix D Serial Number Tag Description132
APPENDIX E: Gguard138
Appendix Fbac Net153
Appendix G: Secure Mode156
Appendix H: Chemical Guide160
Appendix I References176
Appendix J: Setting up the Protector Echo Floor-Mounted Filtered Hood178
Appendix K: Small 54.2" Height Airo Dimensions190

Labconco Protector Echo 180 Series - Appendix K: Small 54.2 Height Airo Dimensions

Table of Contents

Related product manuals