EasyManua.ls Logo

Linak LA12 - User Manual

Linak LA12
39 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
LA12
User Manual

Table of Contents

Questions and Answers

  • T
    Tammy GuerreroJul 27, 2025
    What to do if my Linak Controller has no motor sound or piston rod movement?
    • C
      Corey JamesJul 27, 2025
      If your Linak Controller exhibits no motor sound or piston rod movement, there are several potential causes. First, ensure the actuator is properly connected to the power supply and external control unit, if applicable. Next, check the customer fuse to see if it has burned out. Also, inspect the cable for any damage. If you are using an IC, verify that the power supply polarity is correctly connected and check the wire connection on the internal control unit.
  • S
    Stephen BennettAug 1, 2025
    Why is my Linak Controller actuator running in smaller steps?
    • P
      patrickkingAug 1, 2025
      If your Linak Controller actuator runs in smaller steps, it could be due to an insufficient power supply. Check the power supply to ensure it is adequate. Alternatively, the load might be higher than specified. Reduce the load to see if this resolves the issue.
  • M
    Michael MillerAug 6, 2025
    What to do if my Linak Controller actuator cannot hold the chosen load?
    • M
      Michele RodriguezAug 6, 2025
      If the Linak Controller actuator cannot hold the chosen load, it is possible that the load is higher than specified. Try reducing the load to resolve the issue.
  • F
    Felicia StanleyAug 11, 2025
    Why is my Linak Controller consuming excessive power?
    • R
      Rebecca GibsonAug 11, 2025
      Excessive power consumption in your Linak Controller can be attributed to a couple of reasons. Check for any misalignment or overload in the application and correct it by aligning or reducing the load. Also, try running the actuator without any load.
  • M
    Mackenzie JohnsonAug 16, 2025
    What to do if my Linak Controller actuator cannot lift full load or motor runs too slowly?
    • D
      David AndersonAug 16, 2025
      If your Linak Controller actuator cannot lift a full load or the motor runs too slowly, check the power supply to ensure it is sufficient.
  • S
    Samantha SchultzAug 21, 2025
    What to do if my Linak Controller has no signal or incorrect feedback output?
    • J
      Joshua GarciaAug 21, 2025
      If your Linak Controller shows no signal or provides incorrect feedback output, consider the following: 1. Check the wiring to ensure it is correct. 2. If the signal is constantly high or low, run the actuator to fully extended and retracted positions. 3. If the feedback output is overloaded, reduce the load according to your chosen feedback type.

Summary

Product Preface

User Terms and Conditions

Product Safety Instructions

Mounting and Installation Guidelines

Piston Rod Eye and Inner Tube Instructions

Instructions for turning the piston rod eye and inner tube.

Electrical Installation and Wiring

Recommended Fuse for Actuators without Integrated Controller

Table detailing fuse recommendations based on actuator type and load.

Connection Diagrams and I;O

I;O Specifications

Details input/output signals, specifications, and comments for connection.

Absolute Positioning: Mechanical Potentiometer Feedback

Mechanical Potentiometer Feedback Connection Diagram

Diagram showing connections for mechanical potentiometer feedback.

Mechanical Potentiometer Feedback I;O Specifications

Details input/output specifications for mechanical potentiometer feedback.

Absolute Positioning: Analogue Feedback

Analogue Feedback Connection Diagram

Diagram showing connections for analogue feedback.

Analogue Feedback I;O Specifications

Details input/output specifications for analogue feedback.

Reed Positioning: 4-Wire Actuators

4-Wire Reed Positioning Connection Diagram

Diagram showing connections for 4-wire reed relative positioning.

4-Wire Reed Positioning I;O Specifications

Details input/output specifications for 4-wire reed relative positioning.

Reed Positioning: 3-Wire Actuators

3-Wire Reed Positioning Connection Diagram

Diagram showing connections for 3-wire reed relative positioning.

3-Wire Reed Positioning I;O Specifications

Details input/output specifications for 3-wire reed relative positioning.

IC Actuators: No Endstop Signal

IC Actuator (No Endstop) Connection Diagram

Diagram showing connections for IC actuators without endstop signals.

IC Actuators: With Endstop Signals

IC Actuator with Endstop Signals Connection Diagram

Diagram showing connections for IC actuators with endstop signals.

IC Actuator with Endstop Signals I;O Specifications

Details input/output specifications for IC actuators with endstop signals.

IC Ground Wiring Best Practices

Troubleshooting Common Issues

Technical Specifications

Actuator Dimensional Drawings

12 V Motor Speed and Current Curves

24 V Motor Speed and Current Curves

EMC Test Results: Conducted and Radiated Emissions

LA12 Product Label Information

LA12 Label Symbols Key

Explains the meaning of symbols used on the product label.

Product Ordering Guide

LA12 IC Options

Lists available IC options for the LA12 actuator.

LA12 Memory Positioning Options

Details different memory positioning options for the actuator.

LA12 Material Options

Lists material options for the actuator's inner tube and eye.

LA12 Spindle Type Options

Describes available spindle types (pitch).

LA12 Stroke Options

Specifies available stroke lengths and recommendations.

LA12 Motor Options

Indicates motor voltage options (12 V DC, 24 V DC).

LA12 IP Version Options

Details the available IP protection ratings (IPX1, IP66).

LA12 Cable Options

Lists different cable types and lengths for IC, analogue, and reed configurations.

Product Maintenance and Care

Product Warranty Information

Declaration of Conformity (EMC & RoHS)

Declaration of Incorporation: Machinery Directive

Linak LA12 Specifications

General IconGeneral
BrandLinak
ModelLA12
CategoryController
LanguageEnglish

Related product manuals