Microhard Systems pMDDL5824 - Page 104

© Microhard 104
5.0 AT Command Line Interface
Serial USB - AT Commands
AT Command Description Syntax Effect
AT+MUSBTC Get/Set Serial USB port tcp client configuration
when IP protocol mode is TCP Client
AT+MUSBTC[=<USB Serial>[,<Remote Server IP>,<Remote Server Port>,<Outgoing timeout>
[,<Fast Recovery>]]]
Parameters:
USB Serial : 0 - GS0
Remote Server IP : valid IP address
Remote Server Port : 1 to 65535
Outgoing timeout : 1 to 65535 in seconds
Fast Recovery : 0 - Disable; 1 - Enable
AT&W
AT+MUSBTS Get/Set Serial USB port tcp server configuration
when IP protocol mode is TCP Server
AT+MUSBTS[=<USB Serial>[,<Server Mode>,<Polling Timeout>,<Local Listening
Port>,<Connection timeout>[,<Fast Recovery>]]]
Parameters:
USB Serial : 0 - GS0
Server Mode : 0 - Monitor; 1 - Polling
Polling timeout : 1 to 65535 in seconds
Local Listening Port : 1 to 65535
Connection timeout : 1 to 65535 in seconds
Fast Recovery : 0 - Disable; 1 - Enable
AT&W
AT+MUSBTCS Get/Set Serial USB port tcp client/server configu-
ration when IP protocol mode is TCP Client/
Server
AT+MUSBTCS[=<USB Serial>[,<Remote Server IP>,<Remote Server Port>,<Outgoing timeout>,
<Server Mode>,<Polling Timeout>,<Local Listener Port>,<Incoming timeout>[, <Fast Recov-
ery>]]]
Parameters:
USB Serial : 0 - GS0
Remote Server IP : valid IP address
Remote Server Port : 1 to 65535
Outgoing timeout : 1 to 65535 in seconds
Server Mode : 0 - Monitor; 1 - Polling
Polling timeout : 1 to 65535 in seconds
Local Listening Port : 1 to 65535
Incoming timeout : 1 to 65535 in seconds
Fast Recovery : 0 - Disable; 1 - Enable
AT&W
AT+MUSBUPP Get/Set Serial USB port UDP point to point config-
uration when IP protocol mode is UDP point to
point
AT+MUSBUPP[=<USB Serial>[,<Remote IP>,<Remote Port>,<Listening Port>,<UDP Timeout>]]
Parameters:
USB Serial : 0 - GS0
Remote IP : valid IP address
Remote Port : 1 to 65535
Listening Port : 1 to 65535
UDP Timeout : 1 to 65535 in seconds
AT&W
AT+MUSBUPMP Get/Set Serial USB port UDP point to multipoint
as point configuration when IP protocol mode be
set to UDP point to multipoint (P)
AT+MUSBUPMP[=<USB Serial>[,<Multicast IP>,<Multicast Port>,<Listening Port>,<Time To
Live>,<Multicast Interface>]]
Parameters:
USB Serial: 0 - GS0
Multicast IP: valid IP address
Multicast Port: 1 to 65535
Listening Port: 1 to 65535
Time To Live: 1 to 255 in seconds
Multicast Interface: 0 - default
1 - LAN
AT&W
AT+MUSBUPMM Get/Set Serial USB port UDP point to multipoint
as MP configuration when IP protocol mode be
set to UDP point to multipoint (MP)
AT+MUSBUPMM[=<USB Serial>[,<Remote IP>,<Remote Port>,<Multicast IP>,<Multicast
Port>,<Multicast Interface>]]
Parameters:
USB Serial: 0 - GS0
Remote IP: valid IP address
Remote Port: 1 to 65535
Multicast IP: valid IP address
Multicast Port: 1 to 65535
Multicast Interface: 0 - default
1 - LAN
AT&W