EasyManua.ls Logo

Midea M-thermal Mono Series - Page 62

Midea M-thermal Mono Series
98 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
59
12.4 t_DRYUP The day for w arming up during floor drying up 8 4 15 1 DAY
12.5 t_HIGHPEAK
The continue days in high temperature during floor
drying up
5 3 7 1 DAY
12.6 t_DRYD
The day of dropping temperature during floor drying
up
5 4 15 1 DAY
12.7 T_DRYPEAK
The target peak temperature of w ater flow during
floor drying up
45 30 55 1 °C
12.8 START TIME The start time of floor drying up
Hour
the
present
time(not on
the hour +1,
on the hour
+2)
Minute:00
0:00 23:30 1/30 h/min
12.9 START DATE The start date of floor drying up
The present
date
1/1/2000 31/12/2099 1/1/2001 d/m/y
13.1
AUTO RESTART
COOL/HEAT MODE
Enable or disable the auto restart cooloing/heating
mode. 0=NON,1=YES
1 0 1 1 /
13.2
AUTO RESTART DHW
MODE
Enable or disable the auto restart DHW mode.
0=NON,1=YES
1 0 1 1 /
14.1 POWER INPUT LIMITATION
The type of pow er input limitation, 0=NON,
1~8=TYPE 1~8
0 0 8 1 /
15.1 ON/OFFM1 M2
Define the function of the M1M2 sw itch;
0= REMOTE ON/OFF,1= TBH ON/OFF,2= AHS ON/OFF
0 0 2 1 /
15.2 SMART GRID
Enable or disable the SMART GRID;
0=NON,1=YES
0 0 1 1 /
15.3 T1bTw 2
Enable or disable the T1b(Tw 2) ;
0=NON,1=YES
0 0 1 1 /
15.4 Tbt1
Enable or disable the Tbt1;
0=NON,1=YES
0 0 1 1 /
15.5 Tbt2
Enable or disable the Tbt2;
0=NON,1=YES
0 0 1 1 /
15.6 Ta
Enable or disable the Ta;
0=NON,1=YES
0 0 1 1 /
15.7 SOLAR INPUT
Choose the SOLAR INPUT;
0=NON,1=CN18Tsolar,2=CN11SL1SL2
0 0 2 1 /
15.8 F-PIPE LENGTH
Choose the total length of the liquid pipe(F-PIPE
LENGTH);
0=F-PIPE LENGTH10m,1=F-PIPE LENGTH10m
0 0 1 1 /
15.9 dTbt2 The temperature difference for starting the unit(Tbt2) 15 0 50 1
15.10 RT/Ta_PCB
Enable or disable the RT/Ta_PCB;
0=NON,1=YES
0 0 1 1 /
16.1 PER_START Start-up percentage of multiple units 10 10 100 10 %
16.2 TIME_ADJUST Adjustment time of adding and subtracting units 5 1 60 1 MIN
16.3 ADDRESS RESET Reset the address code of the unit FF 0 15 1 /
17.1 HMI SET
Choose the HMI;
0=MASTER,1=SLAVE
0 0 1 1 /
17.2 HMI ADDRESS FOR BMS Set the HMI address code for BMS 1 1 16 1 /

Table of Contents

Other manuals for Midea M-thermal Mono Series

Related product manuals