MIMAKI SWJ-320 S4 - Table of Contents

© 2013 MIMAKI ENGINEERING CO.,LTD.
Table of Contents R.1.1 P.1
MAINTENANCE MANUAL > Table of Contents
Model SWJ-320S Issued 2012.07.19 Revised 2013.08.28 F/W ver. Remark
Table of Contents
1.3
Rev.
1.Operating Principle
1.1 Basic Operation
1.2 Maintenance Function
1.3 InkSystem
1.3.1 Configuration
2.Electrical Parts
2.1 Block Diagram
2.1.1 Connection Diagram
2.2 Operation Explanation
2.3 Circuit Board Specifications
2.3.1 DC Power Supply (DC37V)
2.3.2 Main PCB assy.
2.3.3 DC Power Supply (DC5V)
2.3.4 Central IO PCB assy.
2.3.5 HDC PCB assy.
2.3.6 Key Board PCB assy.
2.3.7 Optical conversion PCB assy.
2.3.8 FFC Changes PCB assy.
2.3.9 DDRII PRAM(1GB) PCB assy.
2.3.10 ID Contact PCB CN032 Simple assy.
3.Workflow
3.1 Ink Related Parts
3.1.1 Replacement of the Head Unit
3.1.2 Replacement of the INK TANK
3.1.3 Replacement of the Ink Supply Pump
3.2 Driving Parts
3.2.1 Replacement of the X-axis Motor
3.2.2 Replacement of the Y-axis Motor
3.3 Electrical Parts
3.3.1 Replacement of the Main PCB assy.
3.3.2 Replacement of the Power Supply
PBA600F-36-G
3.3.3 Replacement of the Power Supply
PLA600F-36-R
3.3.4 DC Power Supply (DC5V)
3.3.5 Replacement of the Central-IO PCB assy.
3.3.6 Replacement of the 180 LPI Encoder
Sensor
4.Adjustment
4.1 Operation Matrix
4.1.1 For Head adjustment jig
4.2 Adjustment Items
4.2.1 HEAD ADJUST
4.2.2 [HEAD ADJUST] Carriage base tilting
4.2.3 [HEAD ADJUST] Head tilting
4.2.4 [HEAD ADJUST] Stagger / Forward/
backward
4.2.5 [HEAD ADJUST] SLANT ADJUST
4.2.6 [HEAD ADJUST] STAGGER ADJUST
4.2.7 [HEAD ADJUST] POSITION ADJUST
4.2.8 PRINT ADJUST
4.2.9 REPLACE COUNT
4.2.10 DEFAULT SET
4.2.11 CAPPING
4.2.12 ADJUST WIPER
4.2.13 HEAD WASH
4.2.14 INK PURGE
4.2.15 HEAD ID
4.2.16 Serial No.
4.2.17 DEALER No.
4.2.18 FEED COMP.2
4.2.19 LAN CONFIG
4.2.20 Time Set
4.2.21 Nozzle Recovery
4.2.22 CHARGE INK
4.2.23 Power voltage adjustment(DC37V)
4.2.24 Temperature control Upper limit value
setting
4.3 Mechanical Adjustment
4.3.1 Cap height adjustment
4.3.2 Adjustment of the Wiper Height
4.3.3 X-drive belt tension adjustment
4.3.4 Y-drive belt tension adjustment
4.3.5 Y-drive belt (Long) tension adjustment
4.3.6 Positioning of the Encoder Sensor
4.3.7 Slack sensor Optical axis adjustment
4.3.8 Checking path length(for right and left)
of feeding surface
5.Test Items
5.1 Test Function
5.1.1 CHECK PATTERN
5.1.2 SENSOR TEST
5.1.3 MEMORY CHECK
5.1.4 KEYBOARD TEST
5.1.5 LCD TEST
5.1.6 CHECK TEMP.
5.1.7 CHECK INK IC
5.1.8 AGING
5.1.9 CHECK ENCODER
5.1.10 LINEAR ENCODER
5.1.11 TEST HARDWARE
5.1.12 ACTION TEST
5.1.13 LED
5.1.14 SKEW CHECK
5.1.15 INK SUPPLY PUMP
5.1.16 VOLTAGE CHECK
5.2 Other Test
6.Disassembly and Reassembly
6.1 Covers