X Safety considerations
Annex - B Additional RBW filters
A-B.1 Introduction……………………………………………………………………………
A-B.2 MIL-STD-461E Activation procedure (option)…..…………………………………
A-B.3 Analyzer Mode………………………………………………………………………...
A-B.3.1 RBW Selection……………………………………………………………………..
A-B.3.2 MIL Filters…………………………………………………………………………...
A-B.3.3 MIL Filters over 30MHz…………………………………………………………….
A-B.4 Manual Mode………………………………………………………………………….
A-B.4.1 RBW Selection…………………………………………………………..................
A-B.4.2 MIL Filters……………………………………………………………………………
A-B.4.3 Hold Time……………………………………………………………………………
A-B.5 Operating Manual Changes…………………………………………………………
Page
A-B-1
A-B-1
A-B-2
A-B-2
A-B-2
A-B-3
A-B-3
A-B-3
A-B-3
A-B-4
A-B-4
Annex - C Click4E Four Channels Click Meter Option
A-C.1 Introduction……………………………………………………………………………
A-C.2 Installation…………………………………………………………………………….
A-C.2.1 Initial Inspection……………………………………………………………………
A-C.2.2 Packing and Unpacking…………………………………………………………..
A-C.2.3 Preparation for Use………………………………………………………………..
A-C.2.4 Click4E Option mains supply……………………………………………………..
A-C.2.5 PMM 9010 Battery charging………………………………………………………
A-C.2.6 Indication of the battery status on the screen and with PW led………………
A-C.2.7 Environment………………………………………………………………………...
A-C.2.8 Return for Service………………………………………………………………….
A-C.2.9 Equipment Cleaning……………………………………………………………….
A-C.2.10 Equipment ventilation…………………………………………………………….
A-C.2.11 Hardware Installation…………………………………………………………….
A-C.3 Click Mode…………………………………………………………………………….
A-C.3.1 Using an Artificial Mains Network (AMN or LISN) ……………………………..
A-C.3.2 Using the Pulse Limiter……………………………………………………………
A-C.3.3 Click Mode menu………………………………………………………..................
A-C.4 Self Calibration……………………………………………………………………….
A-C.5 Operation………………………………………………………………………………
A-C.5.1 Smart Measure……………………………………………………………………..
A-C.6 Operating Manual Changes…………………………………………………………
A-C-1
A-C-2
A-C-2
A-C-2
A-C-2
A-C-2
A-C-3
A-C-4
A-C-4
A-C-5
A-C-5
A-C-5
A-C-5
A-C-6
A-C-6
A-C-6
A-C-7
A-C-7
A-C-8
A-C-8
A-C-8
Annex - D Measure the insertion loss of a Line Impedance Stabilization
Network (LISN) with a PMM 9010 Receiver
A-D.1 Introduction……………………………………………………………………………
A-D.2 Operation………………………………………………………………………………
A-D.3 Test setup……………………………………………………………………………..
A-D.4 Settings………………………………………………………………………………..
A-D.5 Measure the Insertion Loss (Voltage Division Factor)…………………………...
A-D.6 Connecting the LISN under test……………………………………………….........
A-D.7 Starting the Sweep…………………………………………………………………...
A-D.8 Marker………………………………………………………………………………….
A-D.9 LISNs with PMM Emission Suite…………………………………………...............
A-D-10 Note…………………………………………………………………………………..
A-D-11 PMM LISNs and Passive probes…...…………………………………………….
A-D.12 Conversion table dBμV <> μV <> dBm…………………………………………..
A-D-13 LISN Service kit.....................……………………………………………………..
A-D-1
A-D-1
A-D-1
A-D-1
A-D-2
A-D-2
A-D-3
A-D-4
A-D-4
A-D-5
A-D-6
A-D-7
A-D-8
Annex - E Procedure to connect to the PMM 9010 via a wireless Bluetooth
channel
A-E.1 Introduction……………………………………………………………………………
A-E.2 Wireless connection…………………………………………………………………
A-E.3 Test setup……………………………………………………………………………..
A-E.4 Installation……………………………………………………………………………..
A-E.5 PMM Emission Suite………………………………………….……………………...
A-E-1
A-E-1
A-E-2
A-E-2
A-E-4
To Next Page
Loading...
