NARDA PMM 9010F - Page 8

VIII Safety considerations
13 APD Mode Operating Instructions (Amplitude Probability Distribution)
13.1 Introduction……….……………………………………………………………………
13.2 Pre-conditions and Settings………………..………………………………………..
13.2.1 Entering the function …………..…………………………………………………..
13.2.2 Methods ………………………………………..…………………………………...
13.3 Setup……………………………… …………………………………………………..
13.3.1 Limit 1 E …………………….………………………………………………………
13.3.2 Limit 1 P ……………………….…………………………………………………….
13.3.3 Limit 2 E .……………………………………………………………………………
13.3.4 Limit 2 P …………….……………………………………………………………….
13.3.5 YY Offset …………………………………………………………………………….
13.3.6 Start Frequency …………………………………………………………………….
13.3.7 Stop Frequency……………………………………………………………………..
13.3.8 Num. of freqs ……………………………………………………………................
13.3.9 Time ……………………………..……………………………………………………
13.3.10 Method .…………………………………………………………………................
13.3.11 Search Hold Time ……………………………………………………..................
13.3.12 Conversion Factor …………………………………………………………………
13.3.13 Preselector …………………………………………………………………………
13.3.14 Min. Attenuation……………………………………………………………………
13.3.15 PreAmplifier ……………………………………………………………................
13.4 Operation ……………..……………………………………………………................
13.4.1 Manual (APD)………………………………………………………………………..
13.4.1.1 Frequency ..……………………………………………………………………….
13.4.1.2 Input ……………………………………………………………………………….
13.4.1.3 Clear ………..……………………………………………………………………..
13.4.1.4 Setup ………………………………………………………………………………
13.4.2 Report (APD) .……………………………………………………………………….
13.4.2.1 MHz ……….……………………………………………………………................
13.4.2.2 Pk dBµV ……………………………………………………………………………
13.4.2.3 ∆L Peak …………………………………………………………………………….
13.4.2.4 ∆L1 …………………………………………………………………………………
13.4.2.5 E …………………………………………………………………………………….
13.4.2.6 ∆L2 …………………………………………………………………………………
13.4.2.7 ………………………………………………………………………………………
13.4.2.8 Time ………………………………………………………………………………..
13.4.2.9 P/F …………………………………………………………………………………
13.4.3 Start (APD) ………………………………………………………………………….
13.4.3.1 Sweep running ……………………………………………………………………
13.4.3.2 Signal by signal measurements ………………………………………………..
13.4.3.3 Finish and Next Step …………………………………………………………….
13.4.3.4 Report ……………………………………………………………………………..
13.4.4 Default ……………………………………………………………………………….
13.5 Internal Generator ……………………………………………………………………
13.6 Panel Save and Recall ……………………………………………………................
13-1
13-2
13-3
13-3
13-4
13-4
13-4
13-4
13-5
13-5
13-5
13-5
13-5
13-6
13-6
13-6
13-6
13-6
13-7
13-7
13-8
13-8
13-9
13-10
13-11
13-11
13-12
13-12
13-12
13-12
13-12
13-12
13-12
13-12
13-12
13-12
13-13
13-13
13-13
13-14
13-14
13-14
13-15
13-15