NCR RealScan 7875-7000 - Page 21

56 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

NCR RealScan 7875-7000/8000 Installation Guide

AIP-00342 Release B 06/03

21 of 56

14961

Correct Alignment

Bad Alignment

Scanner Too High

Bad Alignment

Scanner Too Low

High Surface

Low Surface

High Surface

Low Surface

Table of Contents

Table of Contents3
Contents3
Revision Record5
Obtaining Additional Information5
Obtaining Technical Assistance6
System Components7
- NCR Components7
- Sensormatic Components7
Step 1 - Verify and Prepare the Checkstand8
- Checkstand Cutout - Realscan 7875-7000/80008
- Service Clearance9
- Item Diverter9
- Ventilation Requirements10
- Electrical Wiring to the Checkstand11
- Specific Checkstand Modifications12
- Sensormatic Equipment12
Step 2 - Connect the Components13
- Install Sensormatic Antenna13
- Connect Sensormatic Cables14
- Connect Remaining Components15
- Set the Communications Protocol Switch16
Step 3 - Sensormatic Deactivation Setup17
- Power up the System17
- Specific Function Programming18
Step 4 - Install Realscan 787519
- Install Realscan 787519
- Align the Realscan 7875 to the Checkstand20
Step 5 - Calibrate the Scale22
- Set Scale AC Voltage Frequency22
- Exercise the Scale22
- Access the Calibration Switch23
- Calibrate the Scale24
- Verify the Calibration24
- Decreasing Load Test25
- Secure the Calibration Switch26
Step 6 - Set Program Parameters27
- Setting the Program Parameters27
Step 7 - Check the Scanner Operation28
- Scan Sample Tags28
- Check Sensormatic Deactivation System29
- Call Sensormatic29
Operating the Scanner30
Operating the Scale31
Operating the Sensormatic Deactivation System32
- Normal Operation32
- Manual Deactivation33
Cleaning the Realscan 787534
Correcting Scanner Problems35
Correcting Scale Problems36
Isolating Sensormatic Problems37
- Voice Messages37
- Tones37
Programming Worksheets38
- 0 - Communications Protocol38
- 1 - Good Read Tone38
- 2 - Timers39
- 3 - Bar Codes - 139
- 4 - Bar Codes - 240
- 5 - Bar Codes - 341
- 7 - Bar Codes - 441
- 8 - Bar Codes - 542
- 6 - Label Identifiers42
- 0 - RS-232 Parameters - 143
- 1 - RS-232 Parameters - 243
- 2 - RS-232 Prefix Byte44
- 3 - RS-232 Terminator Byte44
- 4 - RS-232 Communications Options44
- 0 - Scale Parameters45
- 2 - Miscellaneous Parameters45
- 6 - Dual Cable Interface Options45
- ASCII Code Chart46
Appendix A - Pan-Oston PO-247
Appendix B - Pan-Oston PO-248
Appendix C - Pan-Oston PO-449
Appendix D - Regulatory Information50
- Federal Communications Commission (FCC) Radio Frequency Interference Statement50
- Voluntary Control Council for Interference (VCCI) Radio Frequency Interference Statement5050
- Canadian Department of Communications Radio Frequency Interference Statement50
- Scale Regulatory51
- Declaration of Conformity52
- Laser Safety53
  - Iec Class 1 Laser Identification54
  - Laser Power54
- AIP-00342 Release B 3 of56

Related product manuals

Preview: NCR RealScan 7837-3000

NCR RealScan 7837-3000

Preview: NCR 7872 Series

NCR 7872 Series