Nederman FlexPAK 800 - Appendix A: PLC Setttings Protocol

44 pages

Save Page as PDF

To Next Page

To Previous Page

FlexPAK 800/1000

Appendix A: PLC sengs protocol

Copy the PLC sengs protocol, ll it in and save it as a service record.

PLC seng Default value Customer specic value

Main Page

Flexpak2
Table of Contents4
Figures4
Preface9
Safety9
Esc Ok10
Flexpak Standby (Standby Mode)10
General10
Nederman Flexpak10
Nederman Flexpak off (off Mode)10
PLC Messages10
Status Messages10
Timeto Service 2000 Hours10
Waiting for Pilot Signal10
Air Temp11
Flexpak Hi Vacuum Unit IDLING Time to Standby11
- Dirtm 00:00 S Ottmr 00:00 H Exhaust Air Temp 60°C11
- Hi Vacuum Unit11
- Time to Standby11
- 05:33M11
- Esc Ok11
- Esc Ok12
- Close Upper Slide Valve V1212
- Emptying bin TVFD Advanced12
- Close Lower Slide Valve V1112
- Flushing Duct12
- Hi Vacuum Unit13
- Isolation Damper Closing Duct13
- Emptying bin AEB Flap Valve13
- Emptying bin TVFD Simple13
- Warning Messages13
- Time for Service13
- Warning! Main Filter Clogged14
- Dustbin Full14
- Bag Replacement Switch Activated14
- Warning Low Vacuum14
- Alarms15
- External Fire Alarm Explosion Detected15
- Frequency Conv Alarm15
- Emergency Stop Activated15
- Low Pressure or Duct Isolation Released16
- Alarm! Hi Vacuum16
- Exhaust Air Temp High16
- Bag Replacement Switch Time out16
- Alarm! Control Filter Clogged17
- TVFD Alarm! Upper Slide Not Closed17
- TVFD Alarm! Upper Slide Not Open17
- TVFD Alarm! Lower Slide Not Closed18
- TVFD Alarm! Lower Slide Not Open18
- TVFD Alarm! Slides in Open Position18
- Alarm! Dustbin Full19
- Alarm! Main Filter Clogged19
- PLC Settings20
- Find a Parameter and Set Its Value20
- Parameter Settings21
- Adjust the Time and Date21
- Set the Weekly Timer22
Kpa -2011
Kpa Dirtm11
Ottmr 00:00 H11
T > 12:00M23
- H-Meter 123
- Ssr_Time23
- Cooltmr24
- Fltclean24
- Dir_Time24
- Weekly Timer24
- Presep25
- MFDPS-Wr25
- Mfdps-Fc25
- BLI-Empt25
- BLI-Wr26
- Aebtme26
- Binopntm26
- CFDPS-Al26
- Tvfdadv26
- Pscflush27
- Binauto27
- Liauto27
- Lsotmr27
- Flushcy227
- Ottmr28
- Flushtmp28
- Cooltmp29
- TVFD-Al-Tmr29
- Brstmr29
- Vac_Low30
- Aeb-Tvfd30
- Flushcy130
- Vaclotm31
- Psifc31
- Preseptm31
- Flushtmr31
- Fcdelay32
- Isovdly32
- Ductisodamp32
- BLI-Alarm33
- MFDPS-Al33
- Dpfclean33
- Emtyidli33
- Clean Cycle34
- Automatic bin Emptying Function34
- AEB-Flap Valve Settings34
- Hardware34
- PLC Settings34
- Timer Settings34
- Simple TVFD Valve Settings34
- Timer Settings35
- Pre-Separator Settings35
- Hardware35
- PLC Settings35
- Timer Settings: Pre-Separator 135
- Timer Settings: Pre-Separator 235
- Advance TVFD Valve Settings36
- Hardware36
- PLC Settings36
- Timer Settings36
- Machining Chips and Swarf Extraction36
- Electrical Connection of Indicator Lamp36
- Pneumatic Filter Cleaning Valve37
- Filter Cleaning Button37
- Filter Cleaning in Standby Mode37
- Filter Cleaning in Running Mode37
- Filter Cleaning Valve Function37
- ATEX Duct Isolation Valve Settings38
- Flush Cycle Settings38
- Flushcy1(T) (Timer)38
- Flushcy2(T) (Timer) (Dual Function)38
- Tuning Duct Isolation Damper Sequence38
- Fcdely(T) Parameter38
- Fcdely(T) Parameter Calculation See, Timing Diagram39
- Default Fcdely(T) Parameter Settings39
- Isovdly(T) Parameter Settings39
- Default Isovdly(T) Parameter Settings39
- Default Clencyl(T) Parameter Settings39
- Procedure to Set Clencyl(T) Parameter39
- Settings TH = Cleaning Pulse Time (FC Valve Opening Time)39
- Total Filter Cleaning Sequence Time40
- Settings TL = Vacuum Load Time40
- FC Start Impulse40
- Appendix A: PLC Setttings Protocol41

Nederman FlexPAK 800 - Appendix A: PLC Setttings Protocol

Table of Contents

Other manuals for Nederman FlexPAK 800

Related product manuals