Nilfisk-Advance SC450 User Manual (English)

Other manuals for Nilfisk-Advance SC450

Instructions For Use100 pages

How-To Guide3 pages

Use & Maintenance2 pages

User Manual76 pages

Questions and Answers:

M
michael92Jul 30, 2025
What to do if my Nilfisk-Advance Floor Machine is not working?
- S
  Scott ThomasJul 30, 2025
  If your Nilfisk-Advance Floor Machine isn't working, several issues could be the cause. It could be due to discharged batteries or inefficient connections; in this case, charge the batteries or clean/repair the connections. Another reason may be broken batteries, so check the battery no-load voltage. Also, the battery charger might be broken and need replacement. Check if the fuses are open and replace them if necessary. Finally, inspect the wiring harness for cuts, presses, or short circuits and repair them.
F
Fernando MooreAug 3, 2025
What to do if the Nilfisk-Advance Scrubber dirty water vacuuming is insufficient?
- R
  Ronald Lewis PhDAug 3, 2025
  If the dirty water vacuuming is insufficient, there are several potential causes. The recovery tank might be full, so empty it. The hose could be disconnected from the squeegee, so connect it. The vacuum grid might be clogged, or the float stuck closed, so clean the grid or check the float. The squeegee could be dirty, or the squeegee blades worn or damaged, so clean and check the squeegee. Finally, the tank cover might not be properly closed, or the gasket damaged, so close the cover or clean/replace the gasket.
T
Tiffany SmithAug 7, 2025
Why is the solution flow to the brush insufficient in my Nilfisk-Advance Scrubber?
- J
  John MoraAug 7, 2025
  If the solution flow to the brush is insufficient, the solution filter may be dirty. Clean the filter to resolve this issue.
C
Christopher WeaverAug 11, 2025
How to fix squeegee marks on the floor from Nilfisk-Advance Scrubber?
- E
  Eileen ShermanAug 12, 2025
  If the squeegee leaves marks on the floor, there might be debris under the squeegee blades, so remove the debris. Alternatively, the squeegee blades may be worn, chipped, or torn, in which case you should replace the blades. Another possibility is that the squeegee hasn't been adjusted with the handwheel, so adjust it.
R
Randy PerezAug 16, 2025
What to do if the motors do not operate on my Nilfisk-Advance SC450 Scrubber?
- T
  tonygrossAug 16, 2025
  If the motors do not operate, the power supply cable or the relevant plug may be broken, in which case you should replace the cable. Alternatively, the switch (41) may be broken, in which case you should replace it.
W
williamsryanAug 20, 2025
What to do if the brush does not work on Nilfisk-Advance Scrubber?
- M
  Misty ReynoldsAug 20, 2025
  If the brush does not work, the push-button (43) may be broken. Replace it to solve the problem.
W
Wyatt SmithAug 25, 2025
Why won't the vacuum system motor turn on in my Nilfisk-Advance SC450?
- M
  Mary HopkinsAug 26, 2025
  If the vacuum system motor does not turn on, the switch (42) may be broken. Replace it to resolve this issue.

Nilfisk-Advance SC450 Specifications

General

Model	SC450
Type	Walk-behind scrubber
Power Source	Battery
Voltage	24 V
Cleaning Width	450 mm
Squeegee Width	450 mm
Brush Motor Power	550 W
Machine Width	450 mm
Machine Length	850 mm
Machine Height	850 mm