Why is my OHAUS Accessories scale unable to calibrate?
Your OHAUS Accessories scale might be unable to calibrate because the LFT security switch is turned on; turn it off. Another possible reason is an incorrect value for the calibration mass; use the correct calibration mass.
What does Error 9.5 mean on my OHAUS Accessories and how to resolve it?
Error 9.5 on your OHAUS Accessories indicates that calibration data is not present. To resolve this, calibrate the scale.
Why can't I change menu settings on my OHAUS Accessories?
If you cannot change menu settings on your OHAUS Accessories, it may be because the Menu button has been locked; enable the Menu button in the Menu. Alternatively, the LFT security switch may need to be switched off.
Why is the battery symbol flashing on my OHAUS Accessories?
The flashing battery symbol on your OHAUS Accessories indicates a low battery. For the i-DT33P model, replace the dry batteries. For the i-DT33XW model, recharge the battery.
Why can't my OHAUS Accessories display weight in the desired weighing unit?
If your OHAUS Accessories cannot display weight in the desired weighing unit, the unit may be disabled. Enable the unit in the Units Menu.
What does REF Err mean on my OHAUS Accessories?
REF Err on your OHAUS Accessories means the average piece of weight (APW) on the pan is too small and less than 0.1d. Replace the batch of samples with a heavier one or change to a scale with readability suitable for your samples.
What does EEP Error mean on my OHAUS Accessories?
EEP Error indicates a corrupted EEPROM data.
What does Error 8.7 mean on OHAUS Measuring Instruments?
If your OHAUS Measuring Instruments displays Error 8.7, the EasyConnectTM base is connected to a powered indicator. Power off the scale completely, reconnect the EasyConnectTM cable, and then power it on again.
Why is my OHAUS Measuring Instruments unable to calibrate?
If you are unable to calibrate your OHAUS Measuring Instruments, ensure that the LFT security switch is turned off. Also, verify that you are using the correct calibration mass.
What does CAL E mean on OHAUS Measuring Instruments?
If your OHAUS Measuring Instruments displays CAL E, the calibration value is outside allowable limits. Use the correct calibration weight.
Defines signal warnings and symbols and provides critical safety precautions for installation and operation.
Specifies the intended applications and environments for the instrument.
Details unpacking contents and connecting power supplies (battery, AC).
Details procedures for opening housing, connecting scale bases, load cells, and RS232.
How to power the indicator on and off.
Steps to enter, use, and configure weighing mode settings.
Steps to enter, use, and configure counting mode settings.
How to set limits, perform checks, and configure check mode settings.
How to set, enter, use, and print totalization results.
Guides on navigating menus and using buttons for input.
Procedures for initial, zero, span, linearity calibration, and testing.
Configuration of units, ranges, graduations, and power-on settings.
Customization of display features like stability, zero range, and backlight.
Activation and selection of available weighing units.
Configuration for RS232, USB, Ethernet, and printing parameters.
Steps for setting up the indicator for trade use, including calibration and security switch.
Procedures for verification by officials and physical sealing of the device.
Instructions for cleaning the indicator housing.
Lists common symptoms, causes, and remedies for issues.
Lists technical specifications for the i-DT33P and i-DT33XW models.
A table mapping geographical coordinates to GEO adjustment codes.
Details the MT Standard Continuous Output format and data structure.
Lists MT-SICS commands and their functions.
Lists OHAUS commands and their functions.
Details printout formats for Check Weighing and Non Check Weighing applications.
General| Display | LCD |
|---|---|
| Power | AC Adapter or Rechargeable Battery |
| Construction | Stainless steel |
| Operating Temperature | -10°C to 40°C |
| Protection | IP65 |
| Units of Measurement | kg, g, lb, oz |
| Calibration | External |
| Approvals | NTEP |
| Interface | RS232 |
| Capacity | 3 kg - 300 kg (depending on model) |
| Platform Size | 300 x 400 mm to 600 x 800 mm |
To Next Page
