Oki MC160MFP - Page 80

44292401TH Rev.1
79 /
Oki Data CONFIDENTIAL
MAINTENANCE
7.3.8 MFP board (MFPB)
NOTE
• For MC160n, boot data is written to the MFP board and firmware data is
written to the FAX control board. To avoid any problem, be sure to replace both the
MFP board and FAX control board at one time.
• When the MFP board is replaced, the setting values for the following items are
cleared. Enter new setting values in the service mode.
For the new setting values, refer to the values set at the shipment, which is shown
on the back side of the label located inside of the front door.
1. Remove the rear cover.
See P.76
2. Remove the right cover.
See P.76
3. Remove the printer control board.
See P.78
4. Remove the FAX control board.
See P.80
5. Remove two screws [1], and remove
the plate [2].
Items for adjustment
CIS MAIN ZOOM
{{
CIS SUB ZOOM
{{
CIS MAIN REGIST
{{
CIS SUB REGIST
{{
ADF SUB ZOOM
 {
ADF MAIN REG
 {
A034F2C068DA
[1][2]
7.3.8 MFP board (MFPB)
NOTE
• For MC160n, boot data is written to the MFP board and firmware data is
written to the FAX control board. To avoid any problem, be sure to replace both the
MFP board and FAX control board at one time.
• When the MFP board is replaced, the setting values for the following items are
cleared. Enter new setting values in the service mode.
For the new setting values, refer to the values set at the shipment, which is shown
on the back side of the label located inside of the front door.
1. Remove the rear cover.
See P.76
2. Remove the right cover.
See P.76
3. Remove the printer control board.
See P.78
4. Remove the FAX control board.
See P.80
5. Remove two screws [1], and remove
the plate [2].
Items for adjustment
CIS MAIN ZOOM {{
CIS SUB ZOOM {{
CIS MAIN REGIST {{
CIS SUB REGIST {{
ADF SUB ZOOM  {
ADF MAIN REG  {
A034F2C068DA
[1][2]
6. Disconnect all connectors and flat
cables from the MFP board.
7. Remove seven screws [1], and
remove the plate [2] and the MFP
board [3].
8. Remove the back up battery [1] on
the MFP board.
NOTE
• When the MFP board is replaced, upgrade the firmware to the latest version.
See P.73
• When the MFP board is replaced with a new one, be sure to execute [BK CLEAR].
See P.129
A034F2C069DA
[1]
[1]
[3] [2]
[1]
A034F2C070DA
[1]
6.3.8 MFP board (MFPB)
7.3.8 MFP board (MFPB)
NOTE
• For MC160n, boot data is written to the MFP board and firmware data is
written to the FAX control board. To avoid any problem, be sure to replace both the
MFP board and FAX control board at one time.
• When the MFP board is replaced, the setting values for the following items are
cleared. Enter new setting values in the service mode.
For the new setting values, refer to the values set at the shipment, which is shown
on the back side of the label located inside of the front door.
1. Remove the rear cover.
See P.76
2. Remove the right cover.
See P.76
3. Remove the printer control board.
See P.78
4. Remove the FAX control board.
See P.80
5. Remove two screws [1], and remove
the plate [2].
Items for adjustment
CIS MAIN ZOOM {{
CIS SUB ZOOM {{
CIS MAIN REGIST {{
CIS SUB REGIST {{
ADF SUB ZOOM 
{
ADF MAIN REG 
{
A034F2C068DA
[1][2]
7.3.8 MFP board (MFPB)
NOTE
• For MC160n, boot data is written to the MFP board and firmware data is
written to the FAX control board. To avoid any problem, be sure to replace both the
MFP board and FAX control board at one time.
• When the MFP board is replaced, the setting values for the following items are
cleared. Enter new setting values in the service mode.
For the new setting values, refer to the values set at the shipment, which is shown
on the back side of the label located inside of the front door.
1. Remove the rear cover.
See P.76
2. Remove the right cover.
See P.76
3. Remove the printer control board.
See P.78
4. Remove the FAX control board.
See P.80
5. Remove two screws [1], and remove
the plate [2].
Items for adjustment
CIS MAIN ZOOM {{
CIS SUB ZOOM {{
CIS MAIN REGIST {{
CIS SUB REGIST {{
ADF SUB ZOOM  {
ADF MAIN REG  {
A034F2C068DA
[1][2]