To Next PageTo Next PageWhy does the Olympus Medical Equipment power fail to turn ON?
If the Olympus Medical Equipment power fails to turn ON, check the following: * Ensure the power switch is turned ON. * Verify the power cord is correctly connected to a wall mains outlet. * Make sure the lamp cover is closed firmly. * Confirm the power switch of the mobile workstation is ON.
What to do if no light is emitted from the endoscope of my Olympus EVIS EXERA III Medical Equipment?
If no light is emitted from the endoscope of your Olympus Medical Equipment, ensure that the examination lamp has been ignited by pressing the lamp button. Also, check that the endoscope or light guide is securely connected to the output socket.
Why is my Olympus EVIS EXERA III Medical Equipment beeping?
If you hear a series of beeps from the Olympus Medical Equipment, it indicates that the temperature of the light source is too high. Turn the light source OFF, make sure the ventilation grills are not covered, allow the light source to cool down, and then turn it ON again.
How to fix Olympus EVIS EXERA III Medical Equipment when the examination lamp does not ignite?
If the examination lamp on your Olympus Medical Equipment does not ignite, consider the following: * Press the lamp button to attempt ignition. * Ensure the examination lamp is installed correctly. If not, install the examination lamp. * If already installed, reinstall the examination lamp. * The examination lamp may be broken, requiring replacement with a new one. * If the examination light is ON, turn it OFF and try igniting the examination lamp again.
Why is NBI observation disabled on my Olympus EVIS EXERA III?
If NBI observation is disabled on your Olympus Medical Equipment, it might be due to an incompatible endoscope or light source cable being connected. Ensure you connect an endoscope and light source cable that are compatible with NBI observation. Also, verify that the NBI observation mode is selected by pressing the observation mode button.
How to reset the lamp usage indicator on Olympus EVIS EXERA III?
If the lamp usage indicator on your Olympus Medical Equipment cannot be reset, make sure the examination lamp is off. Press the lamp button for more than 1 second to extinguish the examination lamp, then press and hold the counter reset button for about 3 seconds. Ensure you press and hold the counter reset button for about 3 seconds.
Why is the air/water feeding not working on my Olympus Medical Equipment?
If the air/water feeding function is not working on your Olympus Medical Equipment, it could be due to the following reasons: * The air pump incorporated in the light source is not working; operate the air/water feeding function. * The endoscope is not connected to the output socket; ensure it is securely connected. * The light guide is connected to the output socket; connect the light guide to an endoscope with the air-feeding function.
What to do if the endoscope cannot be connected to the Olympus EVIS EXERA III Medical Equipment light source?
If the endoscope cannot be connected to the light source of your Olympus Medical Equipment, it might be due to incompatibility. Connect an endoscope that is compatible with the light source.
Why does the Olympus EVIS EXERA III examination lamp ignite automatically?
If the examination lamp ignites automatically when the light source is turned ON in your Olympus Medical Equipment, the auto ignition mode is selected. Set the lamp ignition mode switch on the rear panel to “MANU”.
Why doesn't the brightness change on my Olympus Medical Equipment?
If the brightness does not change on your Olympus Medical Equipment even when the brightness buttons are pressed, the level might be set to the minimum or maximum. Adjust the brightness to an optimum level or try turning the light source OFF and then ON again.
General| Model | EVIS EXERA III |
|---|---|
| Category | Medical Equipment |
| Type | Endoscopy System |
| Manufacturer | Olympus |
| System Type | Video Endoscopy System |
| Video Processor | CV-190 |
| HD Output | Yes |
| Power Requirements | 100-240 V AC, 50/60 Hz |
| Image Quality | HDTV |
| Compatible Endoscopes | EVIS EXERA III series endoscopes |
| Image Enhancement | NBI (Narrow Band Imaging) |
| Light Source | Xenon Lamp |
Covers intended use, applicability, and the importance of thoroughly reviewing the instruction manual.
Provides critical safety warnings and precautions for handling the light source.
Details the nomenclature and function of the front panel components and their indicators.
Details the nomenclature and function of the rear and side panel connectors and features.
Outlines critical safety precautions before installing and connecting the equipment.
Gives general instructions and cautions for physically installing the light source on a stable surface.
Guides on connecting the light source to various Olympus video system centers using specified cables.
Provides instructions and safety warnings for connecting the light source to the power outlet.
Lists essential safety warnings and precautions to observe before performing inspections.
Checks the power supply status, indicators, ventilation, and lamp cover attachment.
Details how to inspect brightness adjustment for both automatic and manual modes.
Lists important warnings and precautions to observe during normal operation.
Details the procedure for powering on the light source and igniting the examination lamp.
Explains how to adjust light intensity for observation in automatic and manual modes.
Provides instructions on safely powering down the entire light source unit.
Provides warnings and instructions for safely replacing the xenon examination lamp.
Outlines the general procedures for reprocessing the light source and accessories.
Describes the workflow for cleaning and disinfecting the light source and its accessories.
Introduces the troubleshooting section and general advice for resolving issues.
Provides a table of common irregularities, their possible causes, and solutions.
